1. Before adding an Hub M1S, please make sure that the mobile phone has been connected with the 2.4GHz Wi-Fi network, and keep the mobile phone as close to the product as possible. 2. If the device fails to be added or the network is not connected for more than 15 minutes after start-up, please long press the device button for more than 10s until the yellow indicator light flashes, and then add the device again. 3. When you hear the voice prompt "waiting to connect, please open Aqara Home App", you can use Aqara Home to add the device. 4. If the device still cannot be added successfully, please power it off, then power it on, and try to add it again. You can also press its button ten times to restore it to the factory settings and try again. Please note that restoring it to the factory settings will clear all usage data, including information about added sub-devices.
1.The hub needs to be plugged into a power outlet. 2.To ensure a stable connection with accessories, it is recommended to install the hub in a central location. 3.Avoid metal obstacles and load-bearing walls between the hub and its accessories, and between the hub and the router.
When the hub alarms, this operation can remove the alarm; when the hub plays ringtone, this operation can stop playing; besides, this operation can turn on/off the night light.
1.Zigbee accessories can only connect to the Aqara Home app via a hub. Select the hub to pair with while connected to the Aqara Home app. 2.If you want to connect a Zigbee accessory to a different hub, please delete it from the homepage in the Aqara Home app first. Then add it again and select the hub you want to pair it with. You can view the list of accessories paired with the hub in the plug-in of the hub.
1.This hub supports up to 32 Zigbee end devices. 2.If you want to add more Zigbee end devices, you can add a Zigbee router to the hub first, and then add further Zigbee end devices. The Zigbee router has extending functionality. After expansion, the hub can support up to 128 Zigbee accessories. 3. Among the Zigbee products of the Aqara and Mijia brands, the product powered by the neutral and live wires is a router, and the product powered by the live wire or by the battery is an end device. Each router can extend to support 16 end devices.
The effective distance range between a accessory and the hub varies depending on the actual indoor environment. For household use, the distance between a accessory and the hub should be no more than 10 meters and there should be no more than two walls between them.
After successfully connecting a Zigbee accessory, try to trigger the accessory before installing it, to see if the accessory's status is updated in the app. Otherwise, refer to the method on how to verify the connection between the accessory and the hub (press reset button for most accessories). The hub will beep twice to indicate that the accessory is within effective range.
1.It may be placed too far from the hub or there may be metal obstacles in between, try moving it closer to the hub. 2.The battery may be depleted, and needs to be replaced. Note: In order to achieve an optimal experience, please update the hub's firmware in time to ensure compatibility and a stable communication between devices.
You can view the device logs to identify different devices. When adding devices, it is recommended to categorize devices based on their installation location or intended use and rename them via the app.
After adding the hub to the Apple Home app, you also need to set up a HomePod, Apple TV (tvOS 11.0 or above), or iPad (iOS 12.0 or above) in order to control the hub remotely. Please refer to Apple Home app notifications for specific operations.
When the hub is added to the Apple Home app, only accessories that support HomeKit are displayed in the Apple Home app. Devices without "Works with Apple HomeKit" authorization cannot access HomeKit.
Click "Automation" on the homepage of the app, then click "+" in the upper right corner of the page, then add the trigger device and conditions in "IF", and then add the execution device and the execution result in "THEN". A scene is a collection of multiple automations and can also be used as the execution result of the automation. For example, you need to set the motion sensor to trigger the light to turn on when it detects someone: click the "+" in the upper right corner of the automation page, select the motion sensor in "IF"> someone moves, and select the light in "THEN" > turn on. And then, you complete the automation settings.
1. According to the characteristics of automations, the execution methods are divided into the cloud method and the local method. It can be viewed in Automation> More settings (three dots in the upper right corner)> Execution method. 2. The automation of cloud execution needs to rely on the network to upload the signal sensed by the trigger device to the cloud, and the cloud then sends the corresponding control command to the execution device. Therefore, once the hub is disconnected from the network, automation cannot be executed. 3. In the automation of local execution, the trigger device will send the sensed signal to the hub, and the hub will send the corresponding control command to the execution device through Zigbee or LAN. So even if the router cannot connect to the external network, as long as the communication connection between the hub and the execution device is normal, automation can still be executed.
You can quickly press the button on the top of the camera three times to initiate ZigBee end device connection. G2H Pro support ZigBee 3.0 protocol and can connect 128 end devices at most.
You can scan the QR code generated by Aqara Home app to connect to internet. After the camera is powered on, please open the app and connect the device to 2.4GHz Wi-Fi, according to the voice prompt. Then, the QR code is generated, and you can scan the QR code through the G2H Pro lens for the network connection.
It supports 2.4GHz IEEE902.11b/g/n Wi-Fi protocol. And it doesn’t support 5GHz Wi-Fi. When connecting the mixing frequency router, it is recommended to separate 2.4GHz and 5GHz Wi-Fi to avoid abnormal connection.
Please check the distance between camera and router, and make sure the Wi-Fi signal is strong enough. If Wi-Fi connecting abnormally, please use Wi-Fi signal amplifier or mobile router to ensure that the device can receive Wi-Fi signals well. Please make sure connecting to 2.4GHz Wi-Fi. Please check if the Wi-Fi SSID or Wi-Fi PWD is correct.
It will take at least 18GB to store one day’s video. Generally, the TF card with 512GB capacity is expected to be stored for 4 weeks, totaling 28 days.
It supports the TF card with CLASS 4 above and format of FAT32. The capacity is 512GB at most. However, We suggest you use the TF card with CLASS 10 above.
It supports magnetic suction and flat installation. You can use 3M glue in the accessories to paste the iron sheet on the non-magnetic material surface, or use fastening screws to fix the iron sheet on the non-magnetic material surface, and then fix the camera.
After the gesture recognition is enabled, it will consume more hardware computing resources, so the face, human shape and pet recognition and other automations related to PTZ are not available. If you disable gesture recognition, other AI functions are available.
Gesture recognition function can be used as the execution condition of automatic control. It can achieve the linkage control of accessory by making a specified static gesture in front of the camera. It is the behavior initiated by the user, and it is not reported as an alarm event or recorded video.
1.Face recognition can be used as the condition of family alert or automatic execution to realize the functions of reporting alarm information and triggering execution automation when detecting unfamiliar or marked faces. 2.Using face recognition for the first time, the Aqara Home APP will guide users to add and synchronize face information to the camera. Face information is stored in the cloud server in the unit of family. Users can synchronize face information to multiple G3 cameras to realize batch operation, and can also add and import faces in the app's setting option. Users can delete face information on their own initiative, and all uploaded face information will be cleared after reset.
The related processes of AI functions(including face, human shape, gesture and pet recognition) will be stopped to ensure the upgrade speed and performance, so the above AI functions are disabled until the upgrade is completed.
Gesture, face, human and pet recognition algorithms all rely on image color information. In night vision mode, the video is gray image, which will affect the effect of AI recognition. It is recommended to experience them only in color mode.
Aqara Camera Hub G3 applies the variable bitrate technology to ensure the 2K Full HD video under various working conditions, and the maximal bitrate is 3.5Mbps when the camera is rotating. To ensure smooth remote viewing, the uplink and downlink bandwidth are required to be higher than that bitrate.
The manual adjustment to the position of the PTZ in the power-on state will lead to the position memory disturbance of the camera. The PTZ can be rotated to the limit position after clicking the one-button PTZ calibration in the Settings - PTZ Settings.
The minimum screen size of the code scanning terminal (such as mobile phone and pad) supported by the camera is 4.7 inches, with the name and password of WLAN of up to 32 ASCII characters (numbers, letters, special symbols), and the best code scanning distance between the QR code and the camera is 8-20cm.
1. The camera supports 128GB MicroSD card and supports the exFat and FAT32 formats 2. Yes. After the device connects to the network successfully, the videos to be saved on the MicroSD card can still be recorded in case of any network disconnection, but these videos saved on the MicroSD card cannot be viewed remotely via app.
1.The associated events label mean that the local video recorded by camera can be marked by different events. For example, if the door and window sensor is enabled or the camera detects any motion, the camera will mark the time and location of this event in the video footage saved in the MicroSD card for further retrieve. 2.Configuration path: “Settings” - “More Settings” - “Alert Setting”, select “Trigger Device” - “Color” - “Save” of the associated events.
There is no limit on the number of connected clients, however, it is recommended that no more than 4 users watch videos simultaneously. The more apps connected, the more processor resource consumed (too many users connected will cause real-time screen lag and delay).
After adding the device to the Apple Home APP, a HomePod or Apple TV (tvOS 11.0 or above) or an iPad (iOS 12.0 or above) that has been set up as the household pivot is required to achieve remote control. Refer to the prompts of Apple Home APP for specific operation.
The Aqara Camera Hub G3 has reserved a standard 1/4" nut hole at the bottom for connecting to the brackets with 1/4" nut, so users can choose the installing brackets recommended by Aqara or other applicable brackets for wall installation or ceiling installation of the camera through the above-mentioned connection method.
Enter the App, click the upper right corner "Settings" - “More Settings” - “Camera Settings” - “Video Settings” - “Installation Methods”, select "Place Upside Down", and the PTZ control and video display will work properly.
The camera supports 2.4/5GHz dual-band Wi-Fi network, and the Wi-Fi networks with WEP, WPA/WPA2, WPA3, WPA-PSK/WPA2-PSK security and encryption mechanism.
Before using the infrared remote control function, the electric appliances to be controlled should be added, then the APP is used as the remote controller to control the electric appliances. If the electric appliance is not in the list of supported devices, you can add the electric appliance through " Customlize ". However, this function is available only for the electric appliance that supports infrared control.
The functions related to camera PTZ control are unavailable temporarily in Apple Home APP until the subsequent update version supports such functions. However, the camera can be controlled the rotation of the PTZ via the Aqara Home APP.
1. Bring your mobile phone closer to the Hub when connecting to Wi-Fi. 2. Connect your phone to Wi-Fi. 3. The phone is required to be connected to the Wi-Fi in the 2.4GHz band. 4. In case of the prompt of Hub connection failure on the mobile phone app, please reset the Hub: Press and hold the button on the Hub for 10s until the orange indicating light is flashing.
Aqara Hub E1 can be applied to the standard USB interface with the output power higher than 2.5W (5V/0.5A), such as sockets, plugs, power adapters and appliances with the USB power supply interface.
1. Wi-Fi relay means that Aqara Hub E1 will generate new WLAN hotspots after being connected to the home wireless router to enlarge the signal cover for other Wi-Fi-appliable devices to connect, which can be used in places with poor Wi-Fi signal including hallway and entry door, and supports up to two accessories. 2. The Wi-Fi relay function can be enabled in the “Settings” - “Wi-Fi Relay” of the app. The device has default hotspot name and password, which can be changed by users.
The connectable distance between the accessory and the Hub varies for different indoor environment. When it is applied in the home environment, it is recommended that the distance between the accessory and the Hub should be no more than 10m, with at most two walls.
The Hub has no built-in loudspeaker and buzzer, so it does not support the local audio alarm, however, it can work with other alarm device on the local area network or in the cloud through automation to achieve alarm function.
1. The accessory may be too far from the Hub, or have a metal shade in between. Please shorten the distance between the accessory and the Hub, and avoid the metal shade. 2. The battery may run down and need to be replaced. Tips: For a better experience, please upgrade the device firmware in time to ensure the compatibility and stable communications.
Please check the log information of the device to recognize devices; When adding a new device, it is suggested to mark the device by the installation location or usage, and rename the new device.
1. The “Preventing accidental deletion” of the Hub is provided for the purpose to avoid the network disconnection of the device due to the misoperation of the function buttons (for example, press and hold a function button for 10s). After enabling this function, the device can only be unbound through the app (when the device is connected to the network normally). 2. The function can be enabled by selecting " Preventing accidental deletion settings" in the Setting in the app.
1. The execution mode of the smart scenes can be divided into cloud execution and local execution. The manual smart scenes are executed via the cloud, and the execution modes of automatic smart scenes can be viewed in the More Settings. 2. For the smart scenes executed via the cloud, it uploads the signal sensed by the trigger device to the cloud via network, which then sends the corresponding control commands to the executing device. In this way, the smart scenes cannot be executed in case of disconnection between the Hub and the network. 3. For the smart scenes executed locally, the trigger device will send the signal sensed to the Hub, which will send the corresponding control commands to the device through Bluetooth, Zigbee or local area network. In this way, the smart scenes can be executed when the Hub is connected to the actuating device normally, even if the router cannot connect to the external network.
1. Zigbee accessories can connect the Aqara Hom APP via the Hub. When connecting the Aqara Home APP, please select the Hub to bind according to the prompt in the app. 2. If you want to change the Hub bound to a Zigbee accessory, please firstly delete the Zigbee accessory from the app homepage and add it again, then re-add the Hub to be bound. 3. You can view the list of accessories bound to the Hub in the app.
1. The Wi-Fi-connectable devices connected the Aqara Home APP enable communication via the router-oriented local area network and Hub, to achieve the smart automations within the local area network; or connect to the cloud via the router, and the cloud sends the executive command to corresponding Wi-Fi-connectable actuating device based on the smart scenarios. 2. According to the working principle, the Wi-Fi-connectable devices can be interconnected through the above two methods, so it does not require or is unable to connect to the Hub.
When the Wi-Fi repeater function is enabled, the IP address is still assigned by the router. 1) When some brands of wireless routers receive frequent connection requests, they may refuse to assign IP addresses, resulting in Wi-Fi repeater unable to connect. It is recommended to restart the route or try to connect again after waiting for a period of time. 2) in some scenarios, the hub may switch back and forth to connect different routers when multiple routers in the same WLAN share SSID but use different channels (such as office environment) , once the channel is changed, the devices under repeater can not establish the corresponding IP relationship with the new route, resulting in the Wi-Fi repeater unable to communicate. It is recommended to experience the Wi-Fi repeater function only in a single router environment.
After adding the device to the Apple Home APP, a HomePod or Apple TV (tvOS 11.0 or above) or an iPad (iOS 12.0 or above) that has been set up as the household pivot is required to achieve remote control. Refer to the prompts of Apple Home APP for specific operation.
When adding the Hub to the Home APP, only the accessories supporting HomeKit function can be displayed on the Home APP; The devices without the authorization of "Works with Apple HomeKit" cannot be connected to the HomeKit.
When some mobile phones add the second device to the repeater, possible appear the mobile phone connects to the repeater first, which leads to the maximum number of two devices allowed to access reached. When the APP“Add device”page show "message send to device",then disconnect the mobile phone from the repeater manually, which can ensure that the second device can successfully connect to the repeater
Aqara Hub M2 is a smart home control center, and also a smart bridge compatible with Apple HomeKit. It supports Wi-Fi or Ethernet network access and interconnection with Zigbee sub-devices. With IR remote control function, it can add and manage different IR devices. Aqara Hub M2 helps you more conveniently control plug, lights, curtain, air conditioner, fan, etc. For more details about the sub-devices that are currently supported by the hub, please log in to www.aqara.com.
Automation can help you do a lot of things automatically, such as setting the timing to turn off the lights at 10 o'clock every night, automatically turning off the air conditioner after you leave home, automatically turning on the corridor light when you arrive home, turning on the lights when people come, and turning off the lights when people go.
In smart home, scene control is a very practical function. You can create a scene through the app and add multiple devices to the scene. For example, you create a "good night" scene, add "bedroom lights", "living room lights" and "corridor light" to the scene, and set all the switch statuses to be off. After the settings are completed, you can execute the "good night" scene to turn off "bedroom lights", "living room lights", "corridor light".
Zigbee technology is a short-range, low power-consumption wireless communication technology. The Hub M2 adapts Zigbee3.0 and has the following advantages: 1.Ultra-low power consumption 2. Short delay. 3. Ad-hoc network, which is compatible with more sub-devices. 4. Strong reliability. 5. High security.
1. You need a 2.4GHz router in your home and it works normally; 2. The hub only supports the 2.4GHz Wi-Fi network. If you use a dual-band router, please turn off the 5GHz Wi-Fi network before adding the hub; 3. If you need to use wired communication between the hub and the router, please use a network cable with an RJ45 network port to connect the LAN port of the hub to that of your router, and wait for the orange and green indicator lights on the side of the network port to light up.
1. It is recommended to install it in the center of the area where the sub-devices are located, to ensure stable communication between the hub and each sub-device. If the distance between the sub-device and the hub is too far, it may cause the offline problem of the sub-device. To avoid this problem, please add another hub and connect the sub-device to it. 2. The hub should not be too far away from the router as much as possible. In order to ensure the stability of Wi-Fi communication, it is best to maintain a straight distance of 2 to 6 meters.
1. Before adding a hub, please make sure that the yellow indicator light of the hub flashes slowly. 2. Please check whether the router is a dual-band router (2.4 GHz Wi-Fi and 5 GHz Wi-Fi are supported at the same time). If yes, please go to the router settings page, set the Wi-Fi hotspot to 2.4 GHz and try again. 3. After long pressing the hub button for 10 seconds and waiting for the yellow indicator light to flash, open the Aqara Home APP, select Add Device in the upper right corner, select "Hub M2" in the hub list, the device can be added according to the prompt of the app. If you are using an iPhone, you can scan the QR code on the bottom of the device to bind it according to the prompt. If binding fails, please long press the button for 10s to restore the hub network, restart the Wi-Fi of the mobile phone, wait for a minute and try again.
1.Please make sure the camera is connected with the 2.4GHz Wi-Fi network; 2.Wi-Fi name or password may contain special characters. Please replace them with ordinary characters and try again; 3.The camera does not support the WAP/WAP2 Wi-Fi network; 4.The camera cannot recognize the QR code generated by the phone. Please make sure the screen of the phone is not less than 4 inches, and cannot scan the QR code under back-lighting. 4.Please check whether the router turns on the Wi-Fi connection watcher function, which causes the network connection failures; 5.Please check whether the router turns on the AP isolation function, which causes the phone cannot search the camera within LAN; 6.It is recommended not to connect it to a bridge network.
1. ”Failed to add accessory”. Due to multiple adding failures, the error information of iOS cache cannot be removed. Please restart the iOS device and reset the camera; 2. ”Accessory already added”. After restarting the iOS device and reset the camera, you can manually enter the HomeKit setup code and add it again; 3. ”Accessory not found”. Please wait for 3 minutes after resetting the camera. You can manually enter the HomeKit setup code and add it again.
Please delete the previously added hub in the "Home" or "Aqara Home" app, restart the Wi-Fi of the phone, long press for 10 seconds to reset the hub until the yellow indicator light flashes, and then add the hub again.
Aqara Hub M2 can be used as the IR control center. After the relevant IR devices are paired through the app, they can be directly controlled through the app or controlled through setting automations, such as turning on the TV, turning on the fan, controlling the air conditioner and so on.
In different indoor environments, the effective communication distance between the sub-device and the hub is different. When used in daily home environment, it is recommended that the distance between the sub-device and the hub should not exceed 10 meters, and there are no more than two walls in the middle.
Triple click: add sub-device Long press: long press the button for 10 seconds to reset the hub. This operation will not delete the device data, such as timing, power, sub-device list and so on. Quickly click 10 times : restore to factory settings. Please clear all data.
Please make sure that the mobile phone connects to the Wi-Fi network where the hub is located, and open the Aqara Home app. On the device page, select the hub that needs to be updated, enter the hub details page, and click firmware update.
1. Long press the hub button for about 10 seconds until the yellow light flashes, indicating that the hub has been unbound from your account. This operation will not delete the device data, such as timing, power, sub-device list and so on. 2. Quickly click the hub button 10 times continuously. After the yellow light flashes, it indicates that the device has restored to the factory settings. This operation will not delete the device data, such as timing, power, sub-device list and so on.
1. Please check whether the power supply of the hub is normal. You can press the button on the hub to check whether the indicator light of the hub is on. If the indicator light is off, please make sure the power supply of the hub is normal; if the indicator light is on, please go to step 2. 2. Please use the mobile phone to connect to the Wi-Fi that the hub is currently connected with, and observe whether the mobile phone can connect to the Internet normally. If it is abnormal, it shows that the Wi-Fi cannot connect to the Internet, please try again after you make sure the Wi-Fi can be used normally; if it is normal, please go to step 3. 3. Please try to unplug the hub and plug it in again. If the blue indicator light flashes, please wait for the blue light to stay always on, and then check whether the hub is offline in the Aqara home app; if the blue light keeps flashing, please bind the hub again in the app ; If the yellow light flashes, please bind the hub again in the app. 4. If the hub goes online after frequently going offline, please place the hub 1-2 meters away from the router with no obstacles (especially metal obstacles) in the middle. 5. Due to performance problems, some routers may cause the device to go offline frequently when there are too many connected Wi-Fi devices. In this case, please try to reduce the number of Wi-Fi devices that have connected to the router, or replace it with a more powerful router. 6. If none of the above steps can solve the hub offline problem, please contact customer service.
1. Please check whether the hub that the sub-device is connected with is offline. If the hub also shows offline status, it means that the sub-device is offline because the hub is offline. Please try to restart the hub and try again. 2. If the hub is online but the sub-device is offline, please check whether the communication between the sub-device and the hub is normal. For more instructions, please refer to "Effective Distance Verification" in the sub-device manual. The voice prompt "connection is normal" indicates that the device and the hub can communicate effectively. If the communication is abnormal, please try to move the sub-device close to the hub or move the hub close to the sub-device and try again. After restarting the app, check whether the sub-device goes online. 3. Please check whether the power supply of the sub-device is normal, and press the button on the sub-device to check if the indicator light of the sub-device is on.
For more details, please refer to "Effective Distance Verification" in the sub-device manual. The indicator light of the sub-device will flash and the hub will play a voice prompt "connection is normal", indicating that the device and the hub can communicate effectively. If the communication is not normal, please try to move the sub-device close to the hub or move the hub close to the sub-device and try again.
The maximum number is 128 (including at least 8 neutral strong electronic devices). Without neutral strong electronic devices, the maximum number of connected sub-devices can only be 32.
Open the "Aqara Home" app. On the "Devices" page, click "[the hub name]" to enter the hub details page. Click "Sub-devices" to view the sub-devices that the current hub has been connected with.
HomeKit is a smart home platform released by Apple. HomeKit allows users to use iOS devices to control all their home accessories labeled "Works with Apple HomeKit".Apple has a "Home" app built into the iOS 10 or later version. Through “Home” app, users can manage all the HomeKit-enabled devices in one platform. Users can create Room in “Home” app, create scenes, such as, “I’m home”, “Away”, set automation, share home ect. Users can use “Home” app to easily and safely control all the HomeKit-enabled accessories. Users can also control the accessories using Siri after naming the accessories. For example, "Turn on the light" or "Turn off the light". "Set the brightness of the light to 50%". "Set the temperature to 20 degrees”. "I’m leaving".
A home hub is the brain of the HomeKit-enabled accessories, through which users can automate and remotely access HomeKit-enabled accessories. With the Apple Home app, you can set up a home hub, remotely control your HomeKit-enabled accessories, give trusted people access, and automate the accessories to do what you need as required. Learn more.
1.Control accessories. Name the accessories in Apple Home or Aqara Home app, distribute them to a specific room and tell Siri , “Turn on the light” “Turn on living room lights” “Turn off lights in my Chicago house” 2. Set scenes. Set scenes in Apple Home or Aqara Home app and name them. Ask Siri to set the following scenes, “Hey Siri. Set the party scene" “Good morning” 3. Check accessory status. Name the accessories in Apple Home or Aqara Home app, distribute them to a specific room and ask Siri, “Is the living room open?” “Living room temperature” “What’s the living room humidity?” Siri voice control of HomeKit-enabled accessories is available on iPhone, Apple Watch, iPad, iPod, Apple TV, HomePod. Learn More.
The HomeKit setup code is a string of 8 digits and it is pasted on the product or its packaging as a QR setup code or digital number . Each product has one unique HomeKit setup code for identification and pairing while adding the accessory. Please keep the HomeKit setup code and avoid sharing the information to others.
You can set HomePod, Apple TV 4K, Apple TV (4th generation), or iPad as a home hub to automate and remotely control HomeKit accessories on iOS devices. A device set as a home hub must be left at home, connected to a home Wi-Fi network, and powered on.
The remote access function cannot be used after the Internet is disconnected, but the accessories can still be accessed through the local area network, the Hub can still be used normally and automation can still operate normally.
1. If you use an iPad, Apple TV, HomePod as a home hub, check if the iPad, Apple TV, HomePod is connected to the router. Do not enable flight mode in iPad. 2. Open the "Home" app and check if the automation is set to disabled. 3. Please check whether the corresponding accessories for automation are offline. Please try again after restoring it online. If the Hub is offline, try restarting the Hub and try again. 4. Open the "Home" app "Home" page on your iOS device, tap the” navigation” icon in the top right corner, click "Home Settings", select your home in the "Home" list, and then under "home hub", see if the home hub shows "Connected." 5. If you use the iPad as a home hub, try reactivating the iPad's WiFi switch and try again.
1. Since the automation function requires the participation of the home hub, make sure that the home hub and the Hub are in the same LAN and that the router Wi-Fi network is stable and reliable. The number of clients connected to the router is preferred to be no more than 20 (depending on router performance). We recommend you to purchase Apple, Mi, TP-LINK, NETGEER branded routers. 2. Using the iPad as a home hub in battery mode, if the iPad's screen is dim, the communication heartbeat interval with the router becomes longer. Therefore, if you do not use the iPad, please keep the iPad in a charging state to ensure when the iPad's screen is dim, it can maintain constant communication with the router. 3. Ensure that the communication between the accessory device and the Hub is reliable. If the communication between the accessory device and the gateway is unstable, the execution will be significantly delayed.
This is because your mobile phone has not backed up or backed up iCloud data for a long time, and the mobile phone does not synchronize the data with iCloud at all times. Therefore, you need to manually synchronize the iCloud data before you can use HomeKit. Solution: In the phone go to the “Settings” – "Your Apple ID Account" - iCloud - iCloud Backup - Click "Manual Backup" and it will be ready after the synchronization is completed.
This is because your mobile phone has not backed up or backed up iCloud data for a long time, and the mobile phone does not synchronize the data with iCloud at all times. Therefore, you need to manually synchronize the iCloud data before you can use HomeKit. Solution: In the phone go to the settings - "Own Apple ID Account" - iCloud - iCloud Backup - Click "Manual Backup" and it will be ready after the synchronization is completed.
In iOS 11 and later, you can use HomeKit accessories such as door locks and sensors. (There are currently several products that support push notifications in Aqara products. They are: Door and Window Sensor, Motion Sensor, Vibration Sensor, and Water Leak Sensor.) Set up notifications to alert you when an accessory detects an anomaly or at a specific time of the day. For example, if you have a Door and Window Sensor installed in your home, you will be notified if the door opens when you are at home. This can be configured as follows: 1. Open the Apple “Home” app. 2. Tap and hold an accessory, then tap Details. 3. Tap Status & Notifications. 4. Turn on "Allow Notifications" and choose one of the following options: 1) Time: Set the time when you want the accessory to send a reminder. 2) Users: Receive reminders from accessories when you or others arrive at or leave your home. If you select this option, you need to configure the home hub, and make sure you can control every accessory in your home that has activated "Share My Location" and "Settings"> "[your name]"> "iCloud"> "Share My Location" and select the device. 5. To complete the operation, tap “Back” in the upper left corner and tap “Finish”. Want to receive notification from HomeKit accessories while you are away from home? Please set up a home hub to remotely access your HomeKit accessories. Learn more .
1. Before adding an Hub M1S, please make sure that the mobile phone has been connected with the 2.4GHz Wi-Fi network, and keep the mobile phone as close to the product as possible. 2. If the device fails to be added or the network is not connected for more than 15 minutes after start-up, please long press the device button for more than 10s until the yellow indicator light flashes, and then add the device again. 3. When you hear the voice prompt "waiting to connect, please open Aqara Home App", you can use Aqara Home to add the device. If you hear the voice prompt "waiting to connect, please open the Mi Home App" in the factory state, you need to press the button twice within 10 seconds after hearing the voice prompt. The device has successfully switched the app platform until you will hear the voice prompt "beep". And then, you can use Aqara Home to add it after the yellow indicator light flashes. 4. If the device still cannot be added successfully, please power it off, then power it on, and try to add it again. You can also press its button ten times to restore it to the factory settings and try again. Please note that restoring it to the factory settings will clear all usage data, including information about added sub-devices.
1.The hub needs to be plugged into a power outlet. 2.To ensure a stable connection with accessories, it is recommended to install the hub in a central location. 3.Avoid metal obstacles and load-bearing walls between the hub and its accessories, and between the hub and the router.
When the hub alarms, this operation can remove the alarm; when the hub plays ringtone, this operation can stop playing; besides, this operation can turn on/off the night light.
1.Zigbee accessories can only connect to the Aqara Home app via a hub. Select the hub to pair with while connected to the Aqara Home app. 2.If you want to connect a Zigbee accessory to a different hub, please delete it from the homepage in the Aqara Home app first. Then add it again and select the hub you want to pair it with. You can view the list of accessories paired with the hub in the plug-in of the hub.
1.This hub supports up to 32 Zigbee end devices. 2.If you want to add more Zigbee end devices, you can add a Zigbee router to the hub first, and then add further Zigbee end devices. The Zigbee router has extending functionality. After expansion, the hub can support up to 128 Zigbee accessories. 3. Among the Zigbee products of the Aqara and Mijia brands, the product powered by the neutral and live wires is a router, and the product powered by the live wire or by the battery is an end device. Each router can extend to support 16 end devices.
The effective distance range between a accessory and the hub varies depending on the actual indoor environment. For household use, the distance between a accessory and the hub should be no more than 10 meters and there should be no more than two walls between them.
After successfully connecting a Zigbee accessory, try to trigger the accessory before installing it, to see if the accessory's status is updated in the app. Otherwise, refer to the method on how to verify the connection between the accessory and the hub (press reset button for most accessories). The hub will beep twice to indicate that the accessory is within effective range.
1.It may be placed too far from the hub or there may be metal obstacles in between, try moving it closer to the hub. 2.The battery may be depleted, and needs to be replaced. Note: In order to achieve an optimal experience, please update the hub's firmware in time to ensure compatibility and a stable communication between devices.
You can view the device logs to identify different devices. When adding devices, it is recommended to categorize devices based on their installation location or intended use and rename them via the app.
After adding the hub to the Apple Home app, you also need to set up a HomePod, Apple TV (tvOS 11.0 or above), or iPad (iOS 12.0 or above) in order to control the hub remotely. Please refer to Apple Home app notifications for specific operations.
When the hub is added to the Apple Home app, only accessories that support HomeKit are displayed in the Apple Home app. Devices without "Works with Apple HomeKit" authorization cannot access HomeKit.
Click "Automation" on the homepage of the app, then click "+" in the upper right corner of the page, then add the trigger device and conditions in "IF", and then add the execution device and the execution result in "THEN". A scene is a collection of multiple automations and can also be used as the execution result of the automation. For example, you need to set the motion sensor to trigger the light to turn on when it detects someone: click the "+" in the upper right corner of the automation page, select the motion sensor in "IF"> someone moves, and select the light in "THEN" > turn on. And then, you complete the automation settings.
1. According to the characteristics of automations, the execution methods are divided into the cloud method and the local method. It can be viewed in Automation> More settings (three dots in the upper right corner)> Execution method. 2. The automation of cloud execution needs to rely on the network to upload the signal sensed by the trigger device to the cloud, and the cloud then sends the corresponding control command to the execution device. Therefore, once the hub is disconnected from the network, automation cannot be executed. 3. In the automation of local execution, the trigger device will send the sensed signal to the hub, and the hub will send the corresponding control command to the execution device through Zigbee or LAN. So even if the router cannot connect to the external network, as long as the communication connection between the hub and the execution device is normal, automation can still be executed.
You can scan the QR code to connect Aqara Smart Camera G2H (Hub) to the network. After the device is powered on, please open the app and connect the device to 2.4GHz Wi-Fi, according to the voice prompt. Then, the QR code is generated, and you can scan the QR code through the G2H lens for the network connection.
1. The distance between the device and the wireless router is too far away or there are many obstacles in the middle. When the Wi-Fi signal is weak, the network connection may be unsuccessful. Please use a Wi-Fi signal amplifier to relay the signal or move the router close to a place where the device can receive the Wi-Fi signal well 2. When the wrong Wi-Fi information is entered, the network connection cannot be completed. Please enter the correct information and try again.
The hub of Aqara Smart Camera G2H (Hub) can be connected with Aqara's other smart sensors and controllers, such as door and window sensor, motion sensor, smart plug, wireless switch and other devices. Through the hub function, you can control these smart devices by app. The hub is the data interaction and control center of the entire home smart devices.
The hub of Aqara Smart Camera G2H (Hub) can be connected through the ZigBee 3.0 protocol, and it can directly support 32 Zigbee terminal devices at most.
Aqara Smart Camera G2H (Hub) supports MicroSD card in FAT32 format, whose reading and writing speed is Class 4 or above. It is recommended to choose the MicroSD card with reading and writing speed of Class10 or above, which supports the maximum capacity of 32GB.
Aqara Smart Camera G2H (Hub) can record high-definition video by default. 8G memory card can record video for 18 hours; 16G memory card can record video for 36 hours; 32G memory card can record video for about 3 days.
1. Some knockoffs of small-capacity memory cards pretend to be sold as large-capacity cards; 2. After some devices have been tested, the MicroSD cards could be maliciously partitioned, and the devices can only read the partition partially; 3. Because the manufacturer's capacity formula is different (the actual measurement unit of normal capacity is 1024KB=1MB, and the manufacturer measurement unit is 1000KB=1MB.), the actual capacity will be slightly smaller than that on the nameplate.
The correlation event means that Aqara Smart Camera G2H (Hub) can be correlated with devices in the same home, such as when door and window sensor is triggered, after detecting human motion, the hub can help locate the time position of the event in the recording area. The maximum number of correlation events is 100. Set a correlation event: click the app > "Correlation events" in the lower right corner > select the trigger device for the correlation event > select the color > save.
There is no limit to the number of clients, and it is recommended that 4 users watch at the same time at most, because the more clients the hub is connected with, the more resources the processor consumes (too many client connections will cause real-time image to freeze, delay, etc.)
After adding the device to the Apple Home app, you need to install a HomePod, Apple TV (tvOS 11.0 or later) or an iPad (iOS 12.0 or later) that has been set as the home center to realize remote control. For specific operations, please refer to the Apple Home app instructions.
The bracket base of Aqara Smart Camera G2H (Hub) contains two powerful magnets, which support magnetic attraction on refrigerators, iron door and other objects, and can also be stuck to non-magnetic attraction objects by using the 3M tape and iron pieces in the accessories. Please use them to install the bracket.
Enter the app, click on the “...” in the upper right corner > More settings > Camera settings > Video settings > Image inversion, and correct the video image by adjusting it up and down or left and right.
The Aqara Hub is a smart Wi-Fi gateway that supports the Aqara Home app and Apple HomeKit. It communicates with subdevices through Zigbee. Users can add various child devices to the Hub, so the system can control the switches, bulbs, curtains, monitor the temperature and humidity, door and window status, detect movement and water leak, and play an alarm or perform an action when triggered. Users can create and manage different scenes with the Apple HomeKit app or the Aqara Home app.
1. Long press the reset button on the Hub for 10 seconds until the yellow light flashes, select the "+" sign on the upper right corner of the home page, select “Aqara Hub”, and scan the HomeKit device code according to the instructions. 2. Tap “No Code or Can’t Scan”. 3. Select the" yellow house" icon "Aqara Hub-XXXX" (if not shown, please wait 1 minute or so, and the app will automatically scan the nearby Hub). 4. In the pop-up dialog box "Add subdevices to network", select Allow (if the dialog box does not pop up, please restart your phone and try again), add the Hub by manually entering the HomeKit code. If "Cannot add subdevices" is shown, the possible reasons and solutions are as follows: 1. The Wi-Fi signal of the router is weak. Please move the Hub closer to the router and try again. 2. Due to repeated adding failures, the Wi-Fi cache of the Hub is not released properly. Please restart your phone and try again. 3. The router’s Wi-Fi is 5 GHz. Please switch to 2.4G Wi-Fi and try again. 4. If your router is an enterprise router, log in to the router setting page to check if "sending mDNS to the wireless terminal " is enabled. If you still can't solve the problem with the above methods, please contact our customer service or send us an email at support@aqara.com, thanks.
1. Please check if the Wi-Fi password is correct. 2. Please check if the Wi-Fi router name or password contains special characters. 3. Check if the Wi-Fi network is connected with the Internet. 4. Check if the Wi-Fi signal of the router is weak. Please move the Hub closer to the router and try again. 5. Check if the Wi-Fi network is 5 GHz. Please switch to 2.4 GHz Wi-Fi and try again.
1. Check if the router Wi-Fi is on. 2. Please check if the Wi-Fi Router password has been changed. 3. If the above two solutions do not work, long press the hub button for 10 seconds until the yellow light flashes and re-add the hub.
1. Long press the hub button for more than 10 seconds until the yellow light flashes, indicating that it has been reset. This operation will not delete the data of the timer, battery, and subdevice list. 2. Press the Hub button 10 times continuously. After the yellow light flashes, it indicates that it has been restored to factory settings. This operation will delete all the data of the timer, battery, and subdevice list.
Please refer to the “Effective range test” in the Quick Start Guide of the device. If the indicator light in the device flashes and the hub makes voice prompts, “Normal Link Confirmed”, it indicates the hub communicates effectively with the child device. If you do not get a voice prompt, please move the device closer to the hub or move the hub closer to the device and try again.
1. Check if the blue light on the hub is flashing. If the blue light is flashing, it means the hub and router are disconnected. Please check if the router works normally. Try to restart the hub and router, then try again. 2. If the blue light on the hub is not flashing. Please restart the hub or the Wi-Fi on your phone. Refresh the app and try again.
1. Check if the hub is online. If the hub is offline, please reconnect the hub and try again. 2. Check if the communication between the device and the hub is normal according to the “Effective Range Test in the quick start guide of the device. Take the Aqara Motion Sensor as an example, short press the reset button, the indicator light on the device will flash and the Hub prompts, "Normal Link Confirmed". It indicates the device and the hub can communicate effectively. Please refresh the app. If the communication is abnormal, try to move the device closer to the hub or move the hub closer to the device and try again. 3. Check if the battery needs to be changed. Single press the button on the device to check if the device indicator is on.
This is because your phone has not backed up iCloud data for a long time, and the mobile phone does not synchronize the data with iCloud at all times. You need to manually synchronize the iCloud data before you can use HomeKit. Solution: 1. In the phone, go to “Settings” > "Your Apple ID Account" > iCloud > iCloud Backup > Click "Manual Backup" and the synchronization is completed 2. Please restart your phone and try again.
1. Make sure you have set up a home hub. You can find instructions here - https://support.apple.com/en-us/HT207057. 2. Open the "Home" page of "Home" app on your iOS device, tap in the upper left corner. Tap "Home Settings", select your home in the "Home" list, and then under "home hub", see if the home hub shows "Connected." . 3. Check if your home hub is connected to the router and is in the same home network with the Aqara Hub.
1. Control child devices. Name the child device in Apple HomeKit, distribute them to a specific room and ask Siri: “Turn on the light” “Turn on the living room lights” “Turn on living room” “Turn off the switch” “Turn on the smart plug” “Turn off the living room lights” “Turn off the lights in my Chicago house” “Set night light to 50%” “Set night light to red” 2. Set scenes. Set scenes in Apple HomeKit and name them. Ask Siri: “Hey Siri. Set the party scene" “Enable at-home scene” “I’m home” “I am leaving” “Good night” “Good morning” 3. Check device status. Name the child devices in Apple HomeKit, distribute them to a specific room and ask Siri: “Is the living room open?” “Living room temperature” “What’s the living room humidity?” “What’s the Water Leak Sensor status”?
Aqara Presence Sensor FP2 can detect the presence or absence of people, falls, entries, exits, approaching, going away and illuminance, and supports real-time tracking of multiple targets and zone settings.
The detection area facilitates users to configure zone automation. 320 cells are provided, so that users may freely select the zones as the trigger areas of automation events, such as setting the sofa, bathroom, study, and dining table. Once the zone is set, it will be added to the automation conditions; 30 zones are supported at most.
The stickers are mainly used to facilitate user reference so that users know more accurately where the target is located. The stickers only affect the user's subjective judgment and do not affect the device's detection performance.
FP2 uses millimeter-wave technology, which is sensitive to moving objects. The more marks set, the more accurate detection the sensor can make. 1) Interference: Living and office spaces often have moving targets such as curtains, fans, green plants moved by wind, and clothes hanging. If the sensor faces these objects, a false alarm may easily occur, so it needs to be marked as an interference source. Currently, the interference source marking is mainly for objects with smaller emission signals, such as green plants and running water. 2) Edge: The setting of the edge is mainly used to counteract false targets caused by a wall or other object reflection signals. The area outside the wall is also suggested to be set as the edge. 3) Entrance and Exit: It can accelerate target creation and deletion speed and improve the user experience.
When used in daily household environments, it is recommended that the distance between the FP2 and the hub should not exceed 20 meters, and they should be under the same AP. There shall be no more than two walls between them.
1) After binding successfully, if the device homepage can display a small icon of a person, and the motion path is consistent with yours, it represents that the device may normally report the location data. (Note: There will be a delay in device display, due to the communication between the device and the server.) 2) If absence detected within 30 seconds after leaving the detection area, it means that the current installation position of the device can meet the main requirements. The quicker it is, the fewer interference there are, and the easier it is to make a correct judgement. If absence event takes a long time or not reported, it represents that there are some interference in the space; the environment may be checked, and the position may be changed. 3) When it is installed, please avoid moving objects and moving objects within a certain period to avoid false alarms.
It may be too far away from the Wi-Fi router or there are metal obstacles in between. You can try to move it closer to the router and avoid metal obstacles. Note: To achieve a better experience, please upgrade the device firmware in a timely manner to ensure compatibility and stable communication between devices.
After setting up the zone, the automation condition will add zone detection, which supports zone automation. For example, if you set up a sofa area, you want to set up the light to turn on when entering the sofa zone: Click the "+ " in the upper right corner of the automation page, select FP2> Zone Detection> Zone > Enter in the "IF" section, and select the light> Light in the "Then" section to complete the automation setting.
When wall-mounted, the horizontal detection angle is 120 degrees, and the radial distance is about 8 meters. When ceiling-mounted at a height of 2.8 meters, it can cover a radius of 2 meters.
Users can configure automation for approaching the sensors or zones, such as turning on the light when approaching the zone. The three levels of distance represent 1 meter, 2 meters, and 3 meters, respectively. After setting it up, entering this threshold from a distance will trigger an approaching event, and leaving this threshold from a close distance will trigger a going-away event.
Aqara smoke alarms use the principle of scattering of light by smoke particles. When the smoke concentration is higher, the more pronounced the scattering is and the stronger the photocurrent generated, thus triggering a fire alarm.
Aqara smoke alarm can be used alone, only local sound and light alarm when not connected to the gateway, and remote alarm and intelligent linkage when connected to ZigBee gateway.
1、Operation error, please re-add the device according to the instructions or the App. 2、The distance between the device and the gateway is too far or too much blocking, it is recommended that the distance is not more than 20 meters and the blocking is not more than two walls, please try again after the device is close to the gateway. 3、 The current gateway does not support the addition of the device, more supported gateway models, please consult customer service
1、The equipment is for indoor installation only. 2、It should not be installed in places such as kitchens where non-fire smoke and vapour are likely to interfere. 3、It should not be installed in places where water vapour is likely to interfere, such as bathrooms. 4、It should be kept at a distance of more than 1.5 meters from ventilation fans, air conditioners and vents. 5、It should be kept at a distance of more than 0.5m from walls, beams and obstructions. 6、Should be installed horizontally, when it is necessary to tilt the installation, the tilt angle should not be greater than 45 degrees. 7、It should not be installed in places where the temperature is below -10C or above 55C. 8、It is recommended to use the screw installation method. 9、When using the paste method of installation, the installation surface must be cleaned beforehand to ensure that the installation surface is smooth, flat, dry and clean;
1、 False alarms caused by cooking fumes or steam. 2、False alarm caused by condensation on the equipment due to humid weather. 3、 The use of incense, electric mosquito incense, etc. caused by false alarms. 4、 Spraying air freshener, insecticide, etc. causes false alarms caused by the accumulation of large amounts of dust inside the equipment.
Press the silence/self-test button on the face of the device; or open the mobile app and click on the "silence" button on the device's alarm page to stop the alarm sound.
1、 Silencing in case of fire alarm, the alarm tone will stop for approx. 80s. 2、 Silencing in case of fault, low battery, the alarm tone will stop for approx. 8 hours.
1、Fire alarm: red light flashes every 1s, with one chirp every 1 second and one pause every three sounds. 2、Linkage alarm: red light flashes once every 4s, with a chirp every 1 second and a pause every three sounds. 3、Battery low: 1 yellow light flashes every 48s, with a chirp every 48s. 4、 Fault: 3 yellow lights flash every 48s, while three chirps every 48s
1、 If the device is already connected to a Zigbee gateway and you want to change to connect to another new gateway, you will need to smoke to reset and reconnect. 2、 Quickly press the silence/self-test button three times and see the green light blink three times in succession to indicate that the device is starting to reset;"
Aqara smoke alarms use the principle of scattering of light by smoke particles. When the smoke concentration is higher, the more pronounced the scattering is and the stronger the photocurrent generated, thus triggering a fire alarm.
Aqara smoke alarm can be used alone, only local sound and light alarm when not connected to the gateway, and remote alarm and intelligent linkage when connected to ZigBee gateway.
1、Operation error, please re-add the device according to the instructions or the App. 2、The distance between the device and the gateway is too far or too much blocking, it is recommended that the distance is not more than 20 meters and the blocking is not more than two walls, please try again after the device is close to the gateway. 3、 The current gateway does not support the addition of the device, more supported gateway models, please consult customer service
1、The equipment is for indoor installation only. 2、It should not be installed in places such as kitchens where non-fire smoke and vapour are likely to interfere. 3、It should not be installed in places where water vapour is likely to interfere, such as bathrooms. 4、It should be kept at a distance of more than 1.5 meters from ventilation fans, air conditioners and vents. 5、It should be kept at a distance of more than 0.5m from walls, beams and obstructions. 6、Should be installed horizontally, when it is necessary to tilt the installation, the tilt angle should not be greater than 45 degrees. 7、It should not be installed in places where the temperature is below -10C or above 55C. 8、It is recommended to use the screw installation method. 9、When using the paste method of installation, the installation surface must be cleaned beforehand to ensure that the installation surface is smooth, flat, dry and clean;
1、 False alarms caused by cooking fumes or steam. 2、False alarm caused by condensation on the equipment due to humid weather. 3、 The use of incense, electric mosquito incense, etc. caused by false alarms. 4、 Spraying air freshener, insecticide, etc. causes false alarms caused by the accumulation of large amounts of dust inside the equipment.
Press the silence/self-test button on the face of the device; or open the mobile app and click on the "silence" button on the device's alarm page to stop the alarm sound.
1、 Silencing in case of fire alarm, the alarm tone will stop for approx. 80s. 2、 Silencing in case of fault, low battery, the alarm tone will stop for approx. 8 hours.
1、Fire alarm: red light flashes every 1s, with one chirp every 1 second and one pause every three sounds. 2、Linkage alarm: red light flashes once every 4s, with a chirp every 1 second and a pause every three sounds. 3、Battery low: 1 yellow light flashes every 48s, with a chirp every 48s. 4、 Fault: 3 yellow lights flash every 48s, while three chirps every 48s
1、 If the device is already connected to a Zigbee gateway and you want to change to connect to another new gateway, you will need to smoke to reset and reconnect. 2、 Quickly press the silence/self-test button three times and see the green light blink three times in succession to indicate that the device is starting to reset;"
1. Install in the area that needs to be monitored, for example in the living room or bedroom (during installation, please refer to the detection range in the quick start guide). 2. A coffee table, shoe cabinet or desk can be used, but ensure that it is installed close to the edge (recommended height is 1.2m/3.94ft to 2.0m/6.56ft); 3. Do not place it on a metal surface or allow something to block the motion sensor P1.
1. Install in the area that needs to be monitored, for example in the living room or bedroom (during installation, please refer to the detection range in the quick start guide). 2. A coffee table, shoe cabinet or desk can be used, but ensure that it is installed close to the edge (recommended height is 1.2m/3.94ft to 2.0m/6.56ft); 3. Do not place it on a metal surface or allow something to block the motion sensor P1.
1. Do not install the sensor on tile, glass, marble and other smooth and moist surfaces, so that the adhesive will not come off. 2. Do not install the sensor on the surface of high-temperature and heat objects such as lighting tubes, so that the adhesive will not come off. 3. Do not install the sensor on rough and uneven surfaces such as wall coverings, so that the adhesive will not come off. 4. Do not put the senor towards hot objects such as electrical appliances when installing to avoid false triggering caused by infrared interference.
1. Do not install the sensor on tile, glass, marble and other smooth and moist surfaces, so that the adhesive will not come off. 2. Do not install the sensor on the surface of high-temperature and heat objects such as lighting tubes, so that the adhesive will not come off. 3. Do not install the sensor on rough and uneven surfaces such as wall coverings, so that the adhesive will not come off. 4. Do not put the senor towards hot objects such as electrical appliances when installing to avoid false triggering caused by infrared interference.
1. Press the reset button on the accessory for 5 seconds. The indicator will flash 3 times before resetting to factory defaults. 2. If a connected sensor needs to be connected to another Hub, it has to be reset first.
1. Press the reset button on the accessory for 5 seconds. The indicator will flash 3 times before resetting to factory defaults. 2. If a connected sensor needs to be connected to another Hub, it has to be reset first.
Possible reasons: 1. Operation error. Please add the accessory according to Add Accessory method again. 2. The accessory is too far away from the Hub. Please move the accessory closer to the Hub. 3. There are more than 32 accessories under this Hub.
Possible reasons: 1. Operation error. Please add the accessory according to Add Accessory method again. 2. The accessory is too far away from the Hub. Please move the accessory closer to the Hub. 3. There are more than 32 accessories under this Hub.
1. The Motion Sensor P1 will flash blue once when it detects motion within the first 5 minutes after joining the network. 2. When the "trigger indicator" is set, a blue light will flash once when motion is detected.
1. The Motion Sensor P1 will flash blue once when it detects motion within the first 5 minutes after joining the network. 2. When the "trigger indicator" is set, a blue light will flash once when motion is detected.
1. The indicator does not flash when the reset button is pressed: the device is not bound to the hub, or the battery is exhausted, or the device is damaged. 2. The indicator flashes once when the reset button is pressed: the device is bound to the hub, but the device is offline. 3. The indicator flashes twice when the reset button is pressed: the device is connected to the hub normally
1. The indicator does not flash when the reset button is pressed: the device is not bound to the hub, or the battery is exhausted, or the device is damaged. 2. The indicator flashes once when the reset button is pressed: the device is bound to the hub, but the device is offline. 3. The indicator flashes twice when the reset button is pressed: the device is connected to the hub normally
Yes. If you do not want a pet to trigger the sensor. Please refer to the detection diagram in the quick start guide and place the motion sensor P1 in a higher location. This way, a pet will not trigger the sensor when it moves on the floor. (Please refer to the quick start guide regarding the installation options).
Yes. If you do not want a pet to trigger the sensor. Please refer to the detection diagram in the quick start guide and place the motion sensor P1 in a higher location. This way, a pet will not trigger the sensor when it moves on the floor. (Please refer to the quick start guide regarding the installation options).
1. There may be some objects with heat in the detection area of the Motion Sensor P1, which interfere with infrared detection. 2. Hot and cold air flow with a large temperature difference may appear in the detection area of the Motion Sensor P1.
1. There may be some objects with heat in the detection area of the Motion Sensor P1, which interfere with infrared detection. 2. Hot and cold air flow with a large temperature difference may appear in the detection area of the Motion Sensor P1.
Click the reset button of the Motion Sensor P1. If the Hub makes voice prompts, "Normal link confirmed", it indicates that the Hub and the Motion Sensor communicates properly; If there is no voice prompt, please move the sensor closer to the Hub and try again. If there is still no voice prompt, the sensor might be deleted or it might run out of battery. Please refer to the accessory adding methods to add the accessory or replace the battery.
Click the reset button of the Motion Sensor P1. If the Hub makes voice prompts, "Normal link confirmed", it indicates that the Hub and the Motion Sensor communicates properly; If there is no voice prompt, please move the sensor closer to the Hub and try again. If there is still no voice prompt, the sensor might be deleted or it might run out of battery. Please refer to the accessory adding methods to add the accessory or replace the battery.
Possible reasons: 1. The accessory is too far away from the Hub, please try to install the accessory closer to the Hub. 2. Low battery or dead battery. Please replace the battery. 3. The accessory is installed on the metal surface and the signal is interfered. Please avoid metal surface.
Possible reasons: 1. The accessory is too far away from the Hub, please try to install the accessory closer to the Hub. 2. Low battery or dead battery. Please replace the battery. 3. The accessory is installed on the metal surface and the signal is interfered. Please avoid metal surface.
The "Detection Interval" is to set the shortest time interval from the previous time of "motion detected" to the next one. For example, the default interval is 10 seconds, then after the motion is detected, no other motion will be detected within 10 seconds.
The "Detection Interval" is to set the shortest time interval from the previous time of "motion detected" to the next one. For example, the default interval is 10 seconds, then after the motion is detected, no other motion will be detected within 10 seconds.
Possible causes: 1. PIR probe or lens has been damaged; 2. The device is in the trigger interval; 3. The device is offline, please confirm whether the device and the hub are connected properly.
Possible causes: 1. PIR probe or lens has been damaged; 2. The device is in the trigger interval; 3. The device is offline, please confirm whether the device and the hub are connected properly.
Press the reset button of the Motion Sensor. If the hub sounds the voice prompt "Connection is normal" or "beep", it means that the communication between the sensor and the hub is normal; if there is no voice prompt, please try to connect the sensor to the hub again; if there is still no voice prompt, the battery of the sensor may be dead, and please replace the battery and try again.
1. The device may be too far away from the hub. Please move the sensor closer to the hub and add the device again. 2. Make sure the hub has connected to the network."
At the moment, the sensor is being initialized, and the value is temporarily not displayed until the data is stable and reliable. This period of time lasts about one to two minutes.
When the temperature is lower than 0 ℃, the screen display may not work well. When the temperature is higher than -20 ℃, the data can be collected and reported normally.
This is determined by the characteristics of the e-ink screen, and the screen flickering may occur several times when it is refreshed, which is normal.
No, an Aqara Hub is required. When vibration is detected, it will trigger the hub to play an alarm. An alert notification will be sent to the phone or interact with other smart accessories via automation.
The "vibration detected" event is triggered once a minute. If the event has been triggered, then it will not be triggered for the next minute. If the vibration persists, the event will be triggered again a minute later.
1. Use a coin to to rotate the battery cover counter clockwise until the cover loosens. 2. Remove the existing battery. Place the new CR2032 battery in the battery compartment and make sure that the positive side of the battery faces upwards. 3. Align the battery cover with the bottom of the Aqara Temperature and Humidity Sensor. Use a coin to rotate the battery cover clockwise until you hear a click. The battery cover is successfully replaced.
After binding the Aqara Vibration Sensor to the hub, single press the reset button on the Vibration Sensor at your desired location before installing. If you hear the hub prompt "normal link confirmed", then the location is suitable for installation. If you do not hear a voice prompt, move the Aqara Vibration Sensor closer to the hub and try again.
1. Line up the sensor unit and the magnet unit according to the mounting mark as shown in the quick start guide. Attach the sensor unit to the fixed surface and the magnet to the surface that will be opened. 2. The distance between the sensor unit and the magnet unit should be less than 22 mm (7/8 inch). 3. The exact position can be changed but ensure that the sensor unit and the magnet unit are installed in alignment. 4. Because of the complex indoor environment, adjusting the distance between the Aqara Hub and the Aqara Door and Window Sensor can improve the overall result. 5. Avoid installing sensors on metal surfaces because of the adverse effect this can have on the signal.
Turn the magnet 90 degrees. It is better to install the sensor unit on a fixed door frame and attach the small magnet unit to the door to protect the sensor better. The sensor unit should be less than 22 mm (7/8 inch) from the magnet. They should not be installed too close to each other to avoid contact and possible damage.
Normally the range of the Aqara Door and Window Sensor is about 7-10 meters (23-33 feet) from the Aqara Hub. In the complex indoor environment, the communication distance will be reduced if there is a wall between the Hub and Door and Window Sensor.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the sensor is reset successfully, and the LED indicator is blinking as expected. 4. Keep the sensor as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
1. The sensor unit and magnet unit might be too far away from each other. Make sure the gap between the sensor unit and the magnet unit is no more than 22 mm (7/8 inch). 2. The Aqara Hub might be too far away from the sensor. Press the reset button of the sensor at the installation location. If the Aqara Hub makes voice prompts, it indicates the Aqara Hub communicates effectively with the sensor. If not, please move the sensor closer to the Aqara Hub. 3. Low battery or dead battery. Please replace the battery. 4. The accessory is installed on a metal surface and the signal is interfered with. Please avoid metal surfaces.
1. Single press the reset button of the sensor, the hub will prompt with the voice message "normal link confirmed" which means the connection between the sensor and the hub is normal. If the hub gives no response, please move the sensor closer to the hub and try again. If the hub remains silent, the sensor might have been removed from the hub or run out of power. Please follow the instructions to add the sensor or replace the battery. 2. Please split the sensor and the magnet and then move them back together, then check the log of the Aqara Door and Window Sensor in the app. The sensor is working properly if the corresponding event has been updated in the log.
1. The Aqara Door and Window Sensor can be installed on the door or window to detect door and window status. 2. Works with other smart devices. If it detects that the door or window opens or closes, and it triggers other devices to turn on or off home appliances or to take other actions.
1. Press the reset button for 3 seconds. The indicator light will flash 3 times before restoring to factory settings. 2. If the bound sensor needs to be bound to another hub, it needs to be reset first.
The Aqara Water Leak Sensor can detect a water leak or water immersion. When the water leak or water immersion occurs, it sends an instant alert notification via the app. It can also interact with other smart accessories with the Aqara Hub.
The Aqara Water Leak Sensor makes use of the electrical conductivity of water. When two probes come into contact with water, a current loop is formed. At the same time, the sensor reports water leak/water immersion status to the Aqara Hub and thereby triggers the alarm or interacts with other smart devices to perform related operations.
The Aqara Water Leak Sensor communicates with the Aqara Hub through the Zigbee wireless protocol. Zigbee technology is a short-distance and low-power consumption wireless communication technology. Compared to other communication protocols, it has the following advantages: 1. Ultra-low power consumption. 2. High security. 3. Accommodates more accessories.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the sensor is reset successfully, and the LED indicator is blinking as expected. 4. Keep the sensor as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
1. The Aqara Hub might be too far away from the sensor. Press the reset button of the sensor at the installation location. If the Aqara Hub makes voice prompts, it indicates the Aqara Hub communicates effectively with the sensor. If not, please move the sensor closer to the Aqara Hub. 2. Low battery or dead battery. Please replace the battery. 3. The accessory is installed on a metal surface and the signal is interfered with. Please avoid metal surfaces.
The Aqara Water Leak Sensor cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Water Leak Sensor to the hub.
The button of the Water Leak Sensor is located at the center of the shell. Trigger the button by holding the top and bottom cover and pressing the "Water Drop" icon.
The Aqara Water Leak Sensor uses one CR2032 lithium button battery. The output voltage of the battery is 3V. Normally, the life of the battery is about two years.
Move the Aqara Temperature and Humidity Sensor close to the hub, open the app, tap "Home" and the tap "+" on the upper right corner to enter the "Add Accessory" page. Select "Temperature and Humidity Sensor" and add it according to instructions. When the hub makes a voice prompt, it indicates that it has been added successfully.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the sensor is reset successfully, and the LED indicator is blinking as expected. 4. Keep the sensor as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
After the Aqara Temperature and Humidity Sensor is connected successfully, press the button of the sensor before it is installed. If the Aqara Hub makes a voice prompt "Normal link confirmed", the current location is Ok. If the Aqara Hub doesn't make a voice prompt, move the sensor closer to the hub and try again.
Possible reasons: 1. The accessory is too far from the hub. Please install it closer to the hub. 2. The battery is dead. Please replace the battery. 3. The accessory has been installed on metal and the signal has been interfered with. The accessory should be installed away from metal.
If you don't want to use it or you want to add it to another hub, long press the reset button for more than 5 seconds until the LED indicator blinks three times. Then the Aqara Hub will make a voice prompt "device deleted". You can also remove it from the app.
Single-click to check the connectivity with the Aqara Hub. It will report the temperature and humidity data to the Aqara Hub. Long press the reset button for more than 5 seconds until the LED indicator blinks three times to add or reset accessories. The Aqara Hub will then make a voice prompt "device deleted".
The Aqara Temperature and Humidity Sensor cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Temperature and Humidity Sensor to the hub.
The Aqara Temperature and Humidity Sensor is suitable for indoor use. Normal operating temperature:-20 to 50°C (-4 to122°F); humidity: 0~100%, non-condensing environment. Do not expose the sensor to rain or vapor. Do not install the sensor in the refrigerator, kitchen or bathroom.
If the temperature, humidity and atmospheric pressure vary only a bit, data will be reported once an hour. If the temperature variation exceeds 0.5℃ (1℉), the humidity variation exceeds 6% and the atmospheric pressure is no less than 25hPa, data will be reported instantly.
When the Aqara Temperature and Humidity Sensor detects that current environment is out of the selected comfort zone, it will push notifications to the mobile phone. This function can be disabled in the app.
The Aqara Temperature and Humidity Sensor can work with other Aqara accessories. For example, when the temperature is higher than the set value, the Aqara Temperature and Humidity Sensor will work with the Aqara Smart Plug to turn on the electric fan; when the humidity is lower than the set value, the Aqara Temperature and Humidity Sensor will work with the Aqara Smart Plug to turn on the humidifier.
If the external network is down, the app control function will no longer be available. But the local control for the sensor will not be affected and its connection with other smart devices will function normally. The sensor can still be triggered, and after being triggered, the sensor will execute corresponding function according to the previous setting in the app. For example, if the Aqara Hub has entered security mode before the connection is down, the Aqara Hub will play an alarm once the sensor is triggered.
Please ensure that the distance between the Aqara Hub and the sensor doesn't exceed 7-10 meters (23-33 feet). Walls are permissible. In this case, it is best to install the sensor at a location closer to the Aqara Hub.
1. Use a coin to to rotate the battery cover counter clockwise until the cover loosens. 2. Remove the existing battery. Place the new CR2032 battery in the battery compartment and make sure that the positive side of the battery faces upwards. 3. Align the battery cover with the bottom of the Aqara Temperature and Humidity Sensor. Use a coin to rotate the battery cover clockwise until you hear a click. The battery cover is successfully replaced.
Press the reset button. If the hub voice prompts, "Normal link confirmed", it indicates that the hub and the Aqara Motion Sensor are communicating properly. If there is no voice prompt, please move the sensor closer to the hub and try again. If there is still no voice prompt, the sensor might be deleted, or its battery may have run down. Please refer to the user manual for instructions to add the device or replace the battery. You can test the Aqara Motion Sensor by putting your hand in front of the lens and check the device records (log). The sensor is working properly if the corresponding event has been updated in the log.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the sensor is reset successfully, and the LED indicator is blinking as expected. 4. Keep the sensor as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
Possible reasons: 1. The accessory is too far from the hub. Please install it closer to the hub. 2. The battery is dead. Please replace the battery. 3. The accessory has been installed on metal and the signal has been interfered with. The accessory should be installed away from metal.
1. Install in the area that needs to detect motion, such as the living room or bedroom (during installation, please refer to the detection range in the quick start guide). 2. A coffee table, shoe cabinet or desk surface can be used, but ensure that it is installed close to the edge (recommended height is 1.2m/3.94ft to 2.1m/6.89ft). 3. Do not place it on a metal surface or allow anything to block the motion sensor.
Yes. It may be triggered by pets because of the passive infrared technology. To avoid this, we suggest you install the Aqara Motion Sensor in a higher position so the pet could not enter the detection area.
The Aqara Motion Sensor goes into sleep mode after it is triggered. One minute later, it can be triggered again. It might be in sleep mode when you were using it.
Within one hour after it connects to the network (new network connection mode), the Aqara Motion Sensor is triggered once every 5 seconds. If it is not triggered within an hour, it automatically enters normal user mode. It is then triggered once every minute.
1. Press and hold the reset button on the device for 5 seconds. The indicator will flash 3 times before resetting to factory settings. 2. If a sensor needs to be paired with another Aqara Hub, it will need to be reset before the new pairing can succeed.
1. To use this device, a Hub that supports Zigbee3.0 is required. Please add the Hub to the APP first according to the instructions. Please open the battery cover with the provided opening pick. 2. Open the app, click "+" in the upper right corner of the homepage, enter the "Add Accessories" page, select "Cube T1 Pro", 3. Select the Hub to be connected, and follow the instructions on the APP. Press and hold the reset button for 5 seconds and wait for the voice prompt of the Hub that indicates the connection is successful.
1. To use this device, a Hub that supports Zigbee3.0 is required. Please add the Hub to the APP first according to the instructions. Please open the battery cover with the provided opening pick. 2. Open the app, click "+" in the upper right corner of the homepage, enter the "Add Accessories" page, select "Cube T1 Pro", 3. Select the Hub to be connected, and follow the instructions on the APP. Press and hold the reset button for 5 seconds and wait for the voice prompt of the Hub that indicates the connection is successful.
Take the Cube and shake it or press the reset button of the Cube. If you hear a voice prompt from the Hub, it indicates that the device and the Hub can communicate effectively.
Take the Cube and shake it or press the reset button of the Cube. If you hear a voice prompt from the Hub, it indicates that the device and the Hub can communicate effectively.
Enter the device homepage, click the "..." icon in the upper right corner, enter the device settings page, click "More Settings", click "Mode Switching", and select the corresponding mode to switch.
Enter the device homepage, click the "..." icon in the upper right corner, enter the device settings page, click "More Settings", click "Mode Switching", and select the corresponding mode to switch.
Open the battery cover of the Cube T1 Pro with the opening pick, take out the battery, replace it with a new CR2450 battery (please note that the battery must be put with the positive side facing up), and put the battery cover back.
Open the battery cover of the Cube T1 Pro with the opening pick, take out the battery, replace it with a new CR2450 battery (please note that the battery must be put with the positive side facing up), and put the battery cover back.
1. Flip 90°: Take the Cube and flip 90° 2. Flip 180°: Take the Cube and flip 180° 3. Tap Twice: Take the Cube and tap twice 4. Push: Push the Cube on a flat surface 5. Rotate: Rotate the Cube on a flat surface 6. Shake: Take the Cube and shake it back and forth twice quickly 7. Triggered after one minute of inactivity: the cube is moved after one minute of inactivity
1. Flip 90°: Take the Cube and flip 90° 2. Flip 180°: Take the Cube and flip 180° 3. Tap Twice: Take the Cube and tap twice 4. Push: Push the Cube on a flat surface 5. Rotate: Rotate the Cube on a flat surface 6. Shake: Take the Cube and shake it back and forth twice quickly 7. Triggered after one minute of inactivity: the cube is moved after one minute of inactivity
1. Face X is up: Put the face X (1～6/any) of the Cube up 2. Shake: Take the Cube and shake it back and forth twice quickly 3. Pick up and hold: pick up the Cube and keep it still 4. When the face X of the Cube is up: face X of the Cube is now facing upwards. 5. Triggered after one minute of inactivity: the cube is moved after one minute of inactivity
1. Face X is up: Put the face X (1～6/any) of the Cube up 2. Shake: Take the Cube and shake it back and forth twice quickly 3. Pick up and hold: pick up the Cube and keep it still 4. When the face X of the Cube is up: face X of the Cube is now facing upwards. 5. Triggered after one minute of inactivity: the cube is moved after one minute of inactivity
1. It may be too far away from the Hub. Please try to put it closer to the Hub. 2. Wireless network interruption or other reasons may cause the Hub to be offline. 3. The battery may be dead. Please replace the battery and try again.
1. It may be too far away from the Hub. Please try to put it closer to the Hub. 2. Wireless network interruption or other reasons may cause the Hub to be offline. 3. The battery may be dead. Please replace the battery and try again.
The Cube T1 Pro cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Cube to the hub.
The Cube T1 Pro cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Cube to the hub.
Both are smart wall switches, the main functions are the same, but the former is the need to connect the neutral wire and the live wire, the latter only need to be connected to the live wire, you need to choose according to the wiring of your home.
Both are smart wall switches, the main functions are the same, but the former is the need to connect the neutral wire and the live wire, the latter only need to be connected to the live wire, you need to choose according to the wiring of your home.
The wall switch is connected to wires. Its most important function is to be able to remotely and intelligently control the power supply and power-off of the connected circuit. If the ordinary light is converted into a smart light, the wall switch is required;
The wireless switch is a remote controller that can control devices such as wall switches through the APP settings, but cannot directly control the ordinary lights separately.
The wall switch is connected to wires. Its most important function is to be able to remotely and intelligently control the power supply and power-off of the connected circuit. If the ordinary light is converted into a smart light, the wall switch is required;
The wireless switch is a remote controller that can control devices such as wall switches through the APP settings, but cannot directly control the ordinary lights separately.
The Smart Wall Switch H1 Pro (With Neutral) supports to upgrade the switch panel to the scene panel with the corresponding number of the switches, for example, the panel of the Smart Wall Switch H1 Pro (With Neutral, Double Rocker) can be upgraded and replaced with the panel of the Scene Panel S1 (Double Switch).
The Smart Wall Switch H1 Pro (With Neutral) supports to upgrade the switch panel to the scene panel with the corresponding number of the switches, for example, the panel of the Smart Wall Switch H1 Pro (With Neutral, Double Rocker) can be upgraded and replaced with the panel of the Scene Panel S1 (Double Switch).
The wall switch will not work normally and the indicator red light is always on. After the switch panel or the power module is matched correctly , it recovers to work normally.
The wall switch will not work normally and the indicator red light is always on. After the switch panel or the power module is matched correctly , it recovers to work normally.
If you want to get satisfied gang-installation effect, you need to separately purchase a Aqara gang frame for installation. Smart Wall Switch H1 can be installed in gang with Aqara Scene Panel S1 and Smart Thermostat T1 to obtain a richer and more convenient smart control experience.
If you want to get satisfied gang-installation effect, you need to separately purchase a Aqara gang frame for installation. Smart Wall Switch H1 can be installed in gang with Aqara Scene Panel S1 and Smart Thermostat T1 to obtain a richer and more convenient smart control experience.
Smart Wall Switch H1 (With Neutral, Triple rocker) as example: There are 5 wiring holes on the back, which are N, L, L3, L2, and L1. The L hole is connected to the live wire, the N hole is connected to the neutral wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (No Neutral, Triple rocker) as example: There are 4 wiring holes on the back, which are L, L3, L2, and L1. The L hole is connected to the live wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (With Neutral, Triple rocker) as example: There are 5 wiring holes on the back, which are N, L, L3, L2, and L1. The L hole is connected to the live wire, the N hole is connected to the neutral wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (No Neutral, Triple rocker) as example: There are 4 wiring holes on the back, which are L, L3, L2, and L1. The L hole is connected to the live wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (With Neutral, Triple Rocker) as example: Connect the live wire and the neutral wire into the L hole and the N hole respectively, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (No Neutral, Triple Rocker) as example: Connect the live wire into the L hole, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (With Neutral, Triple Rocker) as example: Connect the live wire and the neutral wire into the L hole and the N hole respectively, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (No Neutral, Triple Rocker) as example: Connect the live wire into the L hole, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
The live wire is normally red, the neutral wire is usually black or blue and the load wire is usually green or yellow. We suggest you install the switch after a professional electrician has tested the wires using instruments such as voltmeter.
The live wire is normally red, the neutral wire is usually black or blue and the load wire is usually green or yellow. We suggest you install the switch after a professional electrician has tested the wires using instruments such as voltmeter.
Smart Wall Switch H1 (With Neutral): If the load line and the neutral line are swapped, the power-on indicator may work normally, but when the relay is turned on, the switch will burn out. For other wrong installations, the wall switch may not work. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (No Neutral): If the load line of the light is mistakenly connected to the L hole or the live wire is mistakenly connected to L1 or L2, it will not short out, but it may cause the switch to become unresponsive. It can be used after it is correctly connected. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (With Neutral): If the load line and the neutral line are swapped, the power-on indicator may work normally, but when the relay is turned on, the switch will burn out. For other wrong installations, the wall switch may not work. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (No Neutral): If the load line of the light is mistakenly connected to the L hole or the live wire is mistakenly connected to L1 or L2, it will not short out, but it may cause the switch to become unresponsive. It can be used after it is correctly connected. Please strictly follow the instructions for wiring, or ask a professional to install it!
The Smart Wall Switch T1 must be connected to the compatible hub to achieve functions such as coordinated and remote control. After the switch wiring is completed, please open the APP client port, enter the compatible hub, click Add Sub Device, select the corresponding wall switch in the options, and follow the prompts: long press the switch button for more than 8 seconds until the red light is always on for 1 second and the blue light is always on for 1 second, and then the blue light flashes fast. When they are connected successfully, the phone will prompt "connected successfully".
The Smart Wall Switch T1 must be connected to the compatible hub to achieve functions such as coordinated and remote control. After the switch wiring is completed, please open the APP client port, enter the compatible hub, click Add Sub Device, select the corresponding wall switch in the options, and follow the prompts: long press the switch button for more than 8 seconds until the red light is always on for 1 second and the blue light is always on for 1 second, and then the blue light flashes fast. When they are connected successfully, the phone will prompt "connected successfully".
The effective distance between the two devices is 7 to 10 meters with a wall seperating them. If more walls are between the two devices, we recommend shortening the distance.
The effective distance between the two devices is 7 to 10 meters with a wall seperating them. If more walls are between the two devices, we recommend shortening the distance.
The Smart Wall Switch H1 (With Neutral, Single/Double/Triple Rocker) Because the switch is connected to the neutral line and the live line, there is no minimum load requirement. However, the maximum load of the total channels cannot exceed 2200W.
The Smart Wall Switch H1 (No Neutral, Single/Double/Triple Rocker) Under normal circumstances, each channel can load a minimum of 3W energy-saving light or 5W LED light or 16W fluorescent light. However, for some niche brands or poor-quality lights, even if the power is greater than the above requirements due to the internal circuit design, it may cause abnormalities, such as light flashes and switch freezes. Please choose carefully.
Warm reminder: If it is an old-style light with a starter, please replace it with the electronic starter.
The Smart Wall Switch H1 (With Neutral, Single/Double/Triple Rocker) Because the switch is connected to the neutral line and the live line, there is no minimum load requirement. However, the maximum load of the total channels cannot exceed 2200W.
The Smart Wall Switch H1 (No Neutral, Single/Double/Triple Rocker) Under normal circumstances, each channel can load a minimum of 3W energy-saving light or 5W LED light or 16W fluorescent light. However, for some niche brands or poor-quality lights, even if the power is greater than the above requirements due to the internal circuit design, it may cause abnormalities, such as light flashes and switch freezes. Please choose carefully.
Warm reminder: If it is an old-style light with a starter, please replace it with the electronic starter.
When the power of the light, connected to the Smart Wall Switch H1 (No Neutral), is lower than the minimum power requirement, it will randomly flash when the switch turns off. In addition, the Smart Wall Switch H1 (No Neutral) has better support for mainstream brands of lights, but for niche brands or knockoff factories, due to the internal circuit design and material problems, it may cause abnormalities such as the light flashes and the switch freezes. Please choose carefully.
When the power of the light, connected to the Smart Wall Switch H1 (No Neutral), is lower than the minimum power requirement, it will randomly flash when the switch turns off. In addition, the Smart Wall Switch H1 (No Neutral) has better support for mainstream brands of lights, but for niche brands or knockoff factories, due to the internal circuit design and material problems, it may cause abnormalities such as the light flashes and the switch freezes. Please choose carefully.
First, by using the Smart Wall Switch H1 in combination with a wireless switch, it is very easy to achieve dual-control / multi-control. The wireless switch can be placed at most positions of your home to coordinately control the Smart Wall Switch H1;
Second, if the original switches are dual-control ones, only replace one of them with the Smart Wall Switch H1, keep the other ordinary switch short circuit, and replace it with a wireless switch. Otherwise, when the other end powers off, the ZigBee communication module of the Smart Wall Switch H1 cannot power on, so it cannot be controlled automatically.
First, by using the Smart Wall Switch H1 in combination with a wireless switch, it is very easy to achieve dual-control / multi-control. The wireless switch can be placed at most positions of your home to coordinately control the Smart Wall Switch H1;
Second, if the original switches are dual-control ones, only replace one of them with the Smart Wall Switch H1, keep the other ordinary switch short circuit, and replace it with a wireless switch. Otherwise, when the other end powers off, the ZigBee communication module of the Smart Wall Switch H1 cannot power on, so it cannot be controlled automatically.
Both are smart wall switches, the main functions are the same, but the former is the need to connect the neutral wire and the live wire, the latter only need to be connected to the live wire, you need to choose according to the wiring of your home.
Both are smart wall switches, the main functions are the same, but the former is the need to connect the neutral wire and the live wire, the latter only need to be connected to the live wire, you need to choose according to the wiring of your home.
The wall switch is connected to wires. Its most important function is to be able to remotely and intelligently control the power supply and power-off of the connected circuit. If the ordinary light is converted into a smart light, the wall switch is required;
The wireless switch is a remote controller that can control devices such as wall switches through the APP settings, but cannot directly control the ordinary lights separately.
The wall switch is connected to wires. Its most important function is to be able to remotely and intelligently control the power supply and power-off of the connected circuit. If the ordinary light is converted into a smart light, the wall switch is required;
The wireless switch is a remote controller that can control devices such as wall switches through the APP settings, but cannot directly control the ordinary lights separately.
The Smart Wall Switch H1 Pro (With Neutral) supports to upgrade the switch panel to the scene panel with the corresponding number of the switches, for example, the panel of the Smart Wall Switch H1 Pro (With Neutral, Double Rocker) can be upgraded and replaced with the panel of the Scene Panel S1 (Double Switch).
The Smart Wall Switch H1 Pro (With Neutral) supports to upgrade the switch panel to the scene panel with the corresponding number of the switches, for example, the panel of the Smart Wall Switch H1 Pro (With Neutral, Double Rocker) can be upgraded and replaced with the panel of the Scene Panel S1 (Double Switch).
The wall switch will not work normally and the indicator red light is always on. After the switch panel or the power module is matched correctly , it recovers to work normally.
The wall switch will not work normally and the indicator red light is always on. After the switch panel or the power module is matched correctly , it recovers to work normally.
If you want to get satisfied gang-installation effect, you need to separately purchase a Aqara gang frame for installation. Smart Wall Switch H1 can be installed in gang with Aqara Scene Panel S1 and Smart Thermostat T1 to obtain a richer and more convenient smart control experience.
If you want to get satisfied gang-installation effect, you need to separately purchase a Aqara gang frame for installation. Smart Wall Switch H1 can be installed in gang with Aqara Scene Panel S1 and Smart Thermostat T1 to obtain a richer and more convenient smart control experience.
Smart Wall Switch H1 (With Neutral, Triple rocker) as example: There are 5 wiring holes on the back, which are N, L, L3, L2, and L1. The L hole is connected to the live wire, the N hole is connected to the neutral wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (No Neutral, Triple rocker) as example: There are 4 wiring holes on the back, which are L, L3, L2, and L1. The L hole is connected to the live wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (With Neutral, Triple rocker) as example: There are 5 wiring holes on the back, which are N, L, L3, L2, and L1. The L hole is connected to the live wire, the N hole is connected to the neutral wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (No Neutral, Triple rocker) as example: There are 4 wiring holes on the back, which are L, L3, L2, and L1. The L hole is connected to the live wire, and the L1&L2&L3 holes are respectively connected to the load lines of the Three lights; L1 is assigned to the left button of the switch panel,L2 is assigned to the middle button of the switch panel, and L3 is assigned to the right button of the switch panel.
Smart Wall Switch H1 (With Neutral, Triple Rocker) as example: Connect the live wire and the neutral wire into the L hole and the N hole respectively, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (No Neutral, Triple Rocker) as example: Connect the live wire into the L hole, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (With Neutral, Triple Rocker) as example: Connect the live wire and the neutral wire into the L hole and the N hole respectively, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
Smart Wall Switch H1 (No Neutral, Triple Rocker) as example: Connect the live wire into the L hole, and connect the load lines of the lights into the L1, L2 or L3 hole. Use a flat-blade screwdriver to pry up the slot on the switch panel, open the panel, fix the wall switch into the installation box in the wall or on the gang frame (The gang frame needs to be purchased separately) with the enclosed screws, and cover the switch panel.
The live wire is normally red, the neutral wire is usually black or blue and the load wire is usually green or yellow. We suggest you install the switch after a professional electrician has tested the wires using instruments such as voltmeter.
The live wire is normally red, the neutral wire is usually black or blue and the load wire is usually green or yellow. We suggest you install the switch after a professional electrician has tested the wires using instruments such as voltmeter.
Smart Wall Switch H1 (With Neutral): If the load line and the neutral line are swapped, the power-on indicator may work normally, but when the relay is turned on, the switch will burn out. For other wrong installations, the wall switch may not work. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (No Neutral): If the load line of the light is mistakenly connected to the L hole or the live wire is mistakenly connected to L1 or L2, it will not short out, but it may cause the switch to become unresponsive. It can be used after it is correctly connected. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (With Neutral): If the load line and the neutral line are swapped, the power-on indicator may work normally, but when the relay is turned on, the switch will burn out. For other wrong installations, the wall switch may not work. Please strictly follow the instructions for wiring, or ask a professional to install it!
Smart Wall Switch H1 (No Neutral): If the load line of the light is mistakenly connected to the L hole or the live wire is mistakenly connected to L1 or L2, it will not short out, but it may cause the switch to become unresponsive. It can be used after it is correctly connected. Please strictly follow the instructions for wiring, or ask a professional to install it!
The Smart Wall Switch T1 must be connected to the compatible hub to achieve functions such as coordinated and remote control. After the switch wiring is completed, please open the APP client port, enter the compatible hub, click Add Sub Device, select the corresponding wall switch in the options, and follow the prompts: long press the switch button for more than 8 seconds until the red light is always on for 1 second and the blue light is always on for 1 second, and then the blue light flashes fast. When they are connected successfully, the phone will prompt "connected successfully".
The Smart Wall Switch T1 must be connected to the compatible hub to achieve functions such as coordinated and remote control. After the switch wiring is completed, please open the APP client port, enter the compatible hub, click Add Sub Device, select the corresponding wall switch in the options, and follow the prompts: long press the switch button for more than 8 seconds until the red light is always on for 1 second and the blue light is always on for 1 second, and then the blue light flashes fast. When they are connected successfully, the phone will prompt "connected successfully".
The effective distance between the two devices is 7 to 10 meters with a wall seperating them. If more walls are between the two devices, we recommend shortening the distance.
The effective distance between the two devices is 7 to 10 meters with a wall seperating them. If more walls are between the two devices, we recommend shortening the distance.
The Smart Wall Switch H1 (With Neutral, Single/Double/Triple Rocker) Because the switch is connected to the neutral line and the live line, there is no minimum load requirement. However, the maximum load of the total channels cannot exceed 2200W.
The Smart Wall Switch H1 (No Neutral, Single/Double/Triple Rocker) Under normal circumstances, each channel can load a minimum of 3W energy-saving light or 5W LED light or 16W fluorescent light. However, for some niche brands or poor-quality lights, even if the power is greater than the above requirements due to the internal circuit design, it may cause abnormalities, such as light flashes and switch freezes. Please choose carefully.
Warm reminder: If it is an old-style light with a starter, please replace it with the electronic starter.
The Smart Wall Switch H1 (With Neutral, Single/Double/Triple Rocker) Because the switch is connected to the neutral line and the live line, there is no minimum load requirement. However, the maximum load of the total channels cannot exceed 2200W.
The Smart Wall Switch H1 (No Neutral, Single/Double/Triple Rocker) Under normal circumstances, each channel can load a minimum of 3W energy-saving light or 5W LED light or 16W fluorescent light. However, for some niche brands or poor-quality lights, even if the power is greater than the above requirements due to the internal circuit design, it may cause abnormalities, such as light flashes and switch freezes. Please choose carefully.
Warm reminder: If it is an old-style light with a starter, please replace it with the electronic starter.
When the power of the light, connected to the Smart Wall Switch H1 (No Neutral), is lower than the minimum power requirement, it will randomly flash when the switch turns off. In addition, the Smart Wall Switch H1 (No Neutral) has better support for mainstream brands of lights, but for niche brands or knockoff factories, due to the internal circuit design and material problems, it may cause abnormalities such as the light flashes and the switch freezes. Please choose carefully.
When the power of the light, connected to the Smart Wall Switch H1 (No Neutral), is lower than the minimum power requirement, it will randomly flash when the switch turns off. In addition, the Smart Wall Switch H1 (No Neutral) has better support for mainstream brands of lights, but for niche brands or knockoff factories, due to the internal circuit design and material problems, it may cause abnormalities such as the light flashes and the switch freezes. Please choose carefully.
First, by using the Smart Wall Switch H1 in combination with a wireless switch, it is very easy to achieve dual-control / multi-control. The wireless switch can be placed at most positions of your home to coordinately control the Smart Wall Switch H1;
Second, if the original switches are dual-control ones, only replace one of them with the Smart Wall Switch H1, keep the other ordinary switch short circuit, and replace it with a wireless switch. Otherwise, when the other end powers off, the ZigBee communication module of the Smart Wall Switch H1 cannot power on, so it cannot be controlled automatically.
First, by using the Smart Wall Switch H1 in combination with a wireless switch, it is very easy to achieve dual-control / multi-control. The wireless switch can be placed at most positions of your home to coordinately control the Smart Wall Switch H1;
Second, if the original switches are dual-control ones, only replace one of them with the Smart Wall Switch H1, keep the other ordinary switch short circuit, and replace it with a wireless switch. Otherwise, when the other end powers off, the ZigBee communication module of the Smart Wall Switch H1 cannot power on, so it cannot be controlled automatically.
The size of nuts of the thermostat is [M30*1.5mm], and the accessories include: adaptors for the three types of valves (RA, RAV, RAVL), please refer to the operation manual for the installation method.
Every time after the thermostat is powered on, the installation state will be activated ([F11] interface), and it is suggested that the thermostat should be installed on the valve within 5 minutes, after the installation is complete, press the key three times successively to carry out valve calibration, or proceed with networking in accordance with the operation manual, and then carry out valve calibration after the networking is complete. *Reminder: if installation is not complete within 10 min after power-on, please first remove the battery, then put the battery back, and power on for installation.
Because the push rods of different valves have different strokes, it is necessary to carry out calibration of the valve before installation, so that the open/close stroke of the valve can be adaptable, which is an important step to make sure of correct temperature control. After power-on, it is suggested that the thermostat should be installed on the valve within 5 min. You may press the key three times successively to carry out the valve calibration, or do the same with the Aqara Home app.
Possible causes: A. The battery is reversed, so please reinstall the battery (note: wait 30 sec before reinstalling the battery, after the battery is removed). B. Battery power is low. Please replace the battery. C. Product failure. Please contact the vendor for repair or replacement of the product. *Reminder: if the thermostat automatically shuts down, it may be caused by low battery power. In that case, it is suggested that the battery should be replaced.
When networked, the Aqara Temperature & Humidity Sensor should be placed in the same room with the thermostat, 2-3 meters away from the thermostat, but it should not be placed too close to windows. *Reminder: the Aqara Temperature & Humidity Sensor is supported only if it is networked under the same hub.
The thermostat has a built-in temperature sensor, which is used to detect the temperature around the radiator and provide auxiliary temperature control. You can also use the Connect the Temperature Sensor function with the Aqara Home app to network with the Aqara Temperature & Humidity Sensor, to get a better temperature control experience.
Once a temperature value is manually set, the thermostat will regulate and keep the temperature with reference to the set temperature. For instance, under the manual mode, if the Smart Schedule is enabled, the temperature regulation will be performed in accordance with the temperature regulation plan of the Smart Schedule.
In case of prolonged travel in winter (e.g. tourism or business trip), the anti-freeze mode can be enabled to avoid freezing of water pipes due to low temperature, in which case low-temperature operation will be active.
You may set the smart temperature control plan for a day, and activate the plan, then the thermostat will automatically regulate the temperature according to the plan. If the temperature in a certain time frame of the original plan becomes inappropriate due to abrupt weather changes (e.g. sudden rise in outdoor temperature), you may not need to shut down the smart schedule, but can manually regulate the temperature of the current time frame, without creating an impact on the temperature planning of the subsequent time frame, to cope with the sudden changes of weather conditions more flexibly.
When the indoor temperature plunges in a short time, the system will remind the user that it may be resulted from the opening of doors or windows, and will simultaneously close the valve for 30 min to avoid energy waste. You can also set up networking with the Aqara Door and Window Sensor through the Automation function, in order to get a more precise experience of window-open detection.
You can enable/disable the Valve Detection function on the settings page. In order to prevent the prolonged low-temperature or high-temperature state of room temperature from becoming uncomfortable, the thermostat will remind the user of temperature control abnormality when it detects that the room temperature can't reach the set temperature, after heating is started, for the following possible causes: A. The thermostat is not installed correctly. It is suggested that you should remove the battery and put it back 30 sec later, then reinstall the thermostat and calibrate it again, and further wait for a period of time, and then observe whether the fault is eliminated. B. The room temperature is significantly higher than the set temperature due to the incorrect temperature setting. It is suggested that you should re-set the temperature again, wait for a period of time, and then observe whether the fault is eliminated. C. Valve failure. Please replace the valve, reinstall the thermostat, and carry out valve calibration. D. The room is too large (the radiator is not matching) or there is too much ventilation in the room. It is suggested that you should replace the radiator or test whether the room door or window is opened or leaking air. E. The inlet water pressure or inlet water temperature is too low. Please check the inlet water pressure and inlet water temperature. F. Upon networking with the temperature sensors, no linkage is established with the temperature sensor in the same room, or the distance from the temperature sensor to the radiator is remote (it is recommended that the temperature sensor should be placed in the same room with the thermostat, for a distance of 2-3m from the thermostat).
Possible causes: A. The thermostat is not correctly installed. Remove the valve from the thermostat, withdraw the battery and wait for 30 sec, then put the battery back, and reinstall the thermostat, and carry out valve calibration when the device's screen displays the [F11] installation interface (you can press the key three times successively to carry out valve calibration, or do the same with the Aqara Home app). B. Valve failure. After replacing the malfunctioning valve, reinstall the valve and carry out valve calibration according to the above step.
Possible causes: A. Valve failure. After replacing the valve, withdraw the battery and wait for 30 sec, then put the battery back, and reinstall the thermostat, and carry out valve calibration. B. The water inlet temperature of the radiator is low. Please contact professional technicians to overhaul the hot-water pipeline.
Possible causes: A. The thermostat is not networked with the Aqara Home app. Please carry out re-networking. B. The thermostat is too far from the hub, or there are multiple barriers in between. Please adjust the distance, or provide more hubs. C. Battery power is low. Please replace the battery.
Possible causes: A. Battery power is low. Please replace the battery. B. Too much ventilation in the room, which results in excessive heat loss. Please check whether the room door or window is opened or leaking air. C. Check the installation position of the networked temperature sensor, and verify whether the networked temperature sensor is remote from the thermostat (greater than the range of 2-3 m) or placed too close to any ventilation spot (such as a door or window).
Possible causes: A. The networked device (temperature sensor) is offline, malfunctioning, or abnormally networked, etc. Please check the networked device, or carry out re-networking.
The sustainability of the battery depends on the user's temperature regulation frequency and the power-on/power-off frequency of the thermostat. In winter, it is suggested that you should not frequently power on and off the thermostat, to reduce the use frequency of the motor. In the summer season, when heating is suspended, it is suggested that you should power off the thermostat to reduce the loss of the battery's power capacity.
You can organize multiple thermostats in a room into a group to realize collective temperature regulation, power-on/off, mode switching, and create automation. This function only supports device control, and doesn't support device status synchronization.
U-rail, requirements: Bottom slot width ≤ 8 mm, and the bottom surface should be kept flat with no protrusions. I-rail, requirements: Bottom width ≥ 10 mm, and the bottom surface should be kept flat with no protrusions and the circular arc bottom surface is not supported. Caution: There must be no protrusions or steps on the rail caused by installing connecting devices.
The curtain driver of the rod version supports rods with a diameter of 25–32 mm and a smooth surface, and extendable telescopic rods are not supported. Types of curtains: Compatible with grommet curtains and ring top curtains. Please note: The main unit of the Curtain Driver E1 (Rod Version) can also support U- and I-Rails. In this case, for the installation process and compatibility please refer to the user manual or installation video of the Curtain Driver E1 (Track Version). However, fot better performance and compatibility with I-Rails, we suggest using Curtain Driver E1 (Track Version) as it has I-Rail accessories included.
The maximum bearing capacity is 12 kg with U-rails and rods, and about 8 kg with I-rails. The actual bearing capacity will be affected by factors such as wear of curtain rings, aging of rails and dirtiness.
After the curtain driver is clasped in place, the buzzer will beep twice. When you view from the side, the body of the curtain driver should be perpendicular to the bottom of the guide rail, and the drive wheel should not be stuck in the U-rail groove. You may shake the curtains gently by hand. If the position and posture of the curtains can't be changed easily, it shows that the curtain driver is clasped in place.
Check whether the "Open/close curtains manually" function of the curtains has been enabled on the Aqara Home app. Then try to pull the curtain driver in the opposite direction for a distance (about 10 cm) and try again.If you feel it's hard to pull the curtains by hand, you can pull the second or third fold of the curtains.
Press and hold the Set button for 5 seconds, and release it until the indicator blinks orange rapidly and the buzzer beeps. Then, the indicator keeps blinking orange rapidly, which indicates that the curtain driver has been reset successfully.
This may happen due to any of the following reasons: The fully charged curtain driver will deviate from the original route if reinstalled, and it is necessary to set the route for the curtain driver again; The curtain driver is not fully clasped in place (the drive wheel is not fully attached to the guide rail); Please confirm whether there is any foreign object on the curtain rail; Please reset the route for the curtain driver in the Aqara Home app and try again; The curtain driver has insufficient power; Please make sure that there are no protrusions or steps on the rail caused by installing connecting devices; Please make sure that the hanging rings of the curtain driver are in normal condition, and there is no deformation caused by poor-quality materials, such as the rings being pulled apart.
The curtains will stop, but it may cause damage to the curtain due to the strong strength of the curtain driver drive wheel.Please reset the route for the curtain driver after you stop the curtains by pulling.
Go to the device page in the Aqara Home app, click in the top right corner to enter Settings > More settings > Curtain basic settings > Adjust the opening/closing direction of the curtain to make adjustments.
Go to the plug-in in the Aqara Home app, tap in the top right corner to enter Settings > More settings > Curtain basic settings > Curtain style to select Curtain open to the left or Curtain open to the right.
Please make sure that the curtain driver is not blocked by walls, pelmets and other objects, and it will work only after the sensor is exposed to strong light. Note: The ambient light triggered smart connection will only work after the timer and the illumination intensity have been met simultaneously. If it is mainly for scheduled opening and closing of the curtains, you are recommended to use the timer function in automation directly.
There is no option to directly set the ambient light triggered smart connection on the setting page of the curtain driver group, but it is possible to set the function on the setting page of the individual curtain driver device page.
This happens when the internal temperature of the curtain driver is beyond the normal working range.In this case, you need to remove the curtain driver from the curtain rail. If charging is in progress, please disconnect the charging cable and stop charging, and then use it after the temperature returns to normal.
Please check whether the curtains are blocked by other obstacles or dragged to the ground. You will be unable to close the curtains completely in the two cases.
Please confirm whether the curtain driver is clasped in place (the drive wheel is fully attached to the rail).If the curtain driver is not clasped in place, please clasp it in place following the user manual or the instructions in the Aqara Home app and try again.If the curtain driver is clasped in place, please check whether there is any malfunction at the hanging rings of the curtain driver, such as the ring being pulled apart. If there is any malfunction, please use a plier or other tools to restore the ring to its original state, or hang the curtain driver on other rings and try again. Please confirm whether the selected curtain style is consistent with the actual situation when adding the curtain driver to the app;
Given the situation where the length of the track/rod is 1.5m, the weight of the curtain is 12kg, and the device is sheduled to open and close the curtain once a day, the curtain driver can run for around 9 - 10 month. PS: the battery life can be influnced by the friction between the curtain and the track.
U-rail, requirements: Bottom slot width ≤ 8 mm, and the bottom surface should be kept flat with no protrusions. I-rail, requirements: Bottom width ≥ 10 mm, and the bottom surface should be kept flat with no protrusions and the circular arc bottom surface is not supported. Caution: There must be no protrusions or steps on the rail caused by installing connecting devices.
The curtain driver of the rod version supports rods with a diameter of 25–32 mm and a smooth surface, and extendable telescopic rods are not supported. Types of curtains: Compatible with grommet curtains and ring top curtains. Please note: The main unit of the Curtain Driver E1 (Rod Version) can also support U- and I-Rails. In this case, for the installation process and compatibility please refer to the user manual or installation video of the Curtain Driver E1 (Track Version). However, fot better performance and compatibility with I-Rails, we suggest using Curtain Driver E1 (Track Version) as it has I-Rail accessories included.
The maximum bearing capacity is 12 kg with U-rails and rods, and about 8 kg with I-rails. The actual bearing capacity will be affected by factors such as wear of curtain rings, aging of rails and dirtiness.
After the curtain driver is clasped in place, the buzzer will beep twice. When you view from the side, the body of the curtain driver should be perpendicular to the bottom of the guide rail, and the drive wheel should not be stuck in the U-rail groove. You may shake the curtains gently by hand. If the position and posture of the curtains can't be changed easily, it shows that the curtain driver is clasped in place.
Check whether the "Open/close curtains manually" function of the curtains has been enabled on the Aqara Home app. Then try to pull the curtain driver in the opposite direction for a distance (about 10 cm) and try again.If you feel it's hard to pull the curtains by hand, you can pull the second or third fold of the curtains.
Press and hold the Set button for 5 seconds, and release it until the indicator blinks orange rapidly and the buzzer beeps. Then, the indicator keeps blinking orange rapidly, which indicates that the curtain driver has been reset successfully.
This may happen due to any of the following reasons: The fully charged curtain driver will deviate from the original route if reinstalled, and it is necessary to set the route for the curtain driver again; The curtain driver is not fully clasped in place (the drive wheel is not fully attached to the guide rail); Please confirm whether there is any foreign object on the curtain rail; Please reset the route for the curtain driver in the Aqara Home app and try again; The curtain driver has insufficient power; Please make sure that there are no protrusions or steps on the rail caused by installing connecting devices; Please make sure that the hanging rings of the curtain driver are in normal condition, and there is no deformation caused by poor-quality materials, such as the rings being pulled apart.
The curtains will stop, but it may cause damage to the curtain due to the strong strength of the curtain driver drive wheel.Please reset the route for the curtain driver after you stop the curtains by pulling.
Go to the device page in the Aqara Home app, click in the top right corner to enter Settings > More settings > Curtain basic settings > Adjust the opening/closing direction of the curtain to make adjustments.
Go to the plug-in in the Aqara Home app, tap in the top right corner to enter Settings > More settings > Curtain basic settings > Curtain style to select Curtain open to the left or Curtain open to the right.
Please make sure that the curtain driver is not blocked by walls, pelmets and other objects, and it will work only after the sensor is exposed to strong light. Note: The ambient light triggered smart connection will only work after the timer and the illumination intensity have been met simultaneously. If it is mainly for scheduled opening and closing of the curtains, you are recommended to use the timer function in automation directly.
There is no option to directly set the ambient light triggered smart connection on the setting page of the curtain driver group, but it is possible to set the function on the setting page of the individual curtain driver device page.
This happens when the internal temperature of the curtain driver is beyond the normal working range.In this case, you need to remove the curtain driver from the curtain rail. If charging is in progress, please disconnect the charging cable and stop charging, and then use it after the temperature returns to normal.
Please check whether the curtains are blocked by other obstacles or dragged to the ground. You will be unable to close the curtains completely in the two cases.
Please confirm whether the curtain driver is clasped in place (the drive wheel is fully attached to the rail).If the curtain driver is not clasped in place, please clasp it in place following the user manual or the instructions in the Aqara Home app and try again.If the curtain driver is clasped in place, please check whether there is any malfunction at the hanging rings of the curtain driver, such as the ring being pulled apart. If there is any malfunction, please use a plier or other tools to restore the ring to its original state, or hang the curtain driver on other rings and try again. Please confirm whether the selected curtain style is consistent with the actual situation when adding the curtain driver to the app;
Given the situation where the length of the track/rod is 1.5m, the weight of the curtain is 12kg, and the device is sheduled to open and close the curtain once a day, the curtain driver can run for around 9 - 10 month. PS: the battery life can be influnced by the friction between the curtain and the track.
Aqara Curtain Controller B1 supports three control modes such as local button control, sensor linkage control and app remote control. After the Wi-Fi network connection is turned off, the control still can be achieved via local button and sensor linkage.
Long press the reset button on the bottom of the device for 5 seconds until the blue indicator light is on, or you can use Aqara Home App to reset the device
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes. It supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Aqara Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms. In addition, the Aqara Wireless Remote Switch H1 (Double Rocker) also supports low battery alarm, Zigbee signal viewing, distributed networking, and accidental deletion protection, etc.
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes. It supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Aqara Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms. In addition, the Aqara Wireless Remote Switch H1 (Double Rocker) also supports low battery alarm, Zigbee signal viewing, distributed networking, and accidental deletion protection, etc.
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes. It supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Aqara Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms. In addition, the Aqara Wireless Remote Switch H1 (Double Rocker) also supports low battery alarm, Zigbee signal viewing, distributed networking, and accidental deletion protection, etc.
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes, and it supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms.
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes, and it supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms.
The Aqara Wireless Remote Switch H1 (Double Rocker) has two modes, and it supports single press in the high-speed click mode, and 7 functions in the multi-function mode including single press left button, single press right button, double press left button, double press right button, long press left button and long press right button. The high-speed click mode means that the Wireless Remote Switch can respond very fast with the fastest responding speed of 50ms.
The Aqara Wireless Remote Switch H1 (Double Rocker) can be attached to a wall using the adhesive sticker, placed on a desk or table, installed in the Aqara frame or in the traditional 86x86 cm size box (for wall switch). Note: 1. If you need to install the switch in the traditional 86x86 cm size box, you need to open the battery cover first, and use a tool to make a hole in the battery cover before installing it. 2. If you need to install the switch on the Aqara frame, you need to tear off the non-slip silicone pad on the back of the product to expose the screw holes under the silicone pad, and then remove the battery cover for installation.
The Aqara Wireless Remote Switch H1 (Double Rocker) can be attached to a wall using the adhesive sticker, placed on a desk or table, installed in the Aqara frame or in the traditional 86x86 cm size box (for wall switch). Note: 1. If you need to install the switch in the traditional 86x86 cm size box, you need to open the battery cover first, and use a tool to make a hole in the battery cover before installing it. 2. If you need to install the switch on the Aqara frame, you need to tear off the non-slip silicone pad on the back of the product to expose the screw holes under the silicone pad, and then remove the battery cover for installation.
The Aqara Wireless Remote Switch H1 (Double Rocker) can be attached to a wall using the adhesive sticker, placed on a desk or table, installed in the Aqara frame or in the traditional 86x86 cm size box (for wall switch). Note: 1. If you need to install the switch in the traditional 86x86 cm size box, you need to open the battery cover first, and use a tool to make a hole in the battery cover before installing it. 2. If you need to install the switch on the Aqara frame, you need to tear off the non-slip silicone pad on the back of the product to expose the screw holes under the silicone pad, and then remove the battery cover for installation.
1. Single press the button 5 times continuously on the Aqara Wireless Remote Switch H1. If the Aqara Hub prompts voice message "Normal link confirmed", it indicates the hub and the switch are connected. 2. If it does not prompt a voice message, please move the Aqara Wireless Remote Switch H1 closer to the hub and try again. If there are still no voice messages, the Aqara Wireless Remote Switch H1 might be deleted or the battery has run down. Please refer to the user manual for instructions to add again or replace the battery. 3. Single press the Aqara Wireless Remote Switch H1 several times and go to the homepage of the app and select the Aqara Wireless Remote Switch H1 to check. If the status changes, it indicates the accessory is working properly.
1. Single press the button 5 times continuously on the Aqara Wireless Remote Switch H1. If the Aqara Hub prompts voice message "Normal link confirmed", it indicates the hub and the switch are connected. 2. If it does not prompt a voice message, please move the Aqara Wireless Remote Switch H1 closer to the hub and try again. If there are still no voice messages, the Aqara Wireless Remote Switch H1 might be deleted or the battery has run down. Please refer to the user manual for instructions to add again or replace the battery. 3. Single press the Aqara Wireless Remote Switch H1 several times and go to the homepage of the app and select the Aqara Wireless Remote Switch H1 to check. If the status changes, it indicates the accessory is working properly.
1. Single press the button 5 times continuously on the Aqara Wireless Remote Switch H1. If the Aqara Hub prompts voice message "Normal link confirmed", it indicates the hub and the switch are connected. 2. If it does not prompt a voice message, please move the Aqara Wireless Remote Switch H1 closer to the hub and try again. If there are still no voice messages, the Aqara Wireless Remote Switch H1 might be deleted or the battery has run down. Please refer to the user manual for instructions to add again or replace the battery. 3. Single press the Aqara Wireless Remote Switch H1 several times and go to the homepage of the app and select the Aqara Wireless Remote Switch H1 to check. If the status changes, it indicates the accessory is working properly.
1. Long press the button of the switch for more than 10 seconds. The indicator light will flash 3 times before restoring to factory settings. 2. If the switch has been bound to a hub, please delete it from the app first. 3. If the accidental deletion protection function is activated, please turn off this function before deleting the device.
1. Long press the button of the switch for more than 10 seconds. The indicator light will flash 3 times before restoring to factory settings. 2. If the switch has been bound to a hub, please delete it from the app first. 3. If the accidental deletion protection function is activated, please turn off this function before deleting the device.
1. Long press the button of the switch for more than 10 seconds. The indicator light will flash 3 times before restoring to factory settings. 2. If the switch has been bound to a hub, please delete it from the app first. 3. If the accidental deletion protection function is activated, please turn off this function before deleting the device.
The accidental deletion protection function prevents the device from being reset or unbound due to accidental operation. If this function is enabled on the Hub setting page, when the network is normal, long pressing the reset button will not reset the Aqara Wireless Remote Switch H1 (Double Rocker) or make it off-line.
The accidental deletion protection function prevents the device from being reset or unbound due to accidental operation. If this function is enabled on the Hub setting page, when the network is normal, long pressing the reset button will not reset the Aqara Wireless Remote Switch H1 (Double Rocker) or make it off-line.
The accidental deletion protection function prevents the device from being reset or unbound due to accidental operation. If this function is enabled on the Hub setting page, when the network is normal, long pressing the reset button will not reset the Aqara Wireless Remote Switch H1 (Double Rocker) or make it off-line.
If the battery power of the Aqara Wireless Remote Switch H1 (Double Rocker) is lower than 2.7V for 3 consecutive hours, the device will report a low battery alert.
If the battery power of the Aqara Wireless Remote Switch H1 (Double Rocker) is lower than 2.7V for 3 consecutive hours, the device will report a low battery alert.
If the battery power of the Aqara Wireless Remote Switch H1 (Double Rocker) is lower than 2.7V for 3 consecutive hours, the device will report a low battery alert.
To put it simply, the child devices do not require a hub, and the controller and actuator can be networked in pairs. For some Zigbee 3.0 strong current devices (such as the Aqara Smart Plug T1), you can click the reset button for 3 times when the device is not bound to any hub to enable the distributed networking mode. At this time, press and hold the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10s to start distributed networking.
To put it simply, the child devices do not require a hub, and the controller and actuator can be networked in pairs. For some Zigbee 3.0 strong current devices (such as the Aqara Smart Plug T1), you can click the reset button for 3 times when the device is not bound to any hub to enable the distributed networking mode. At this time, press and hold the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10s to start distributed networking.
To put it simply, the child devices do not require a hub, and the controller and actuator can be networked in pairs. For some Zigbee 3.0 strong current devices (such as the Aqara Smart Plug T1), you can click the reset button for 3 times when the device is not bound to any hub to enable the distributed networking mode. At this time, press and hold the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10s to start distributed networking.
1. Open the app, go to the accessory adding page, select the Aqara Wireless Remote Switch H1 (Double Rocker), and select the corresponding hub. 2. Long press the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10 seconds, and the indicator light will flash for 3 times quickly when the device is powered on. 3. If the device is successfully bound, the indicator light will flash twice slowly; if it fails, it will stay on for 1s. 4. If the addition fails, please move the switch closer to the hub and try again.
1. Open the app, go to the accessory adding page, select the Aqara Wireless Remote Switch H1 (Double Rocker), and select the corresponding hub. 2. Long press the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10 seconds, and the indicator light will flash for 3 times quickly when the device is powered on. 3. If the device is successfully bound, the indicator light will flash twice slowly; if it fails, it will stay on for 1s. 4. If the addition fails, please move the switch closer to the hub and try again.
1. Open the app, go to the accessory adding page, select the Aqara Wireless Remote Switch H1 (Double Rocker), and select the corresponding hub. 2. Long press the button of the Aqara Wireless Remote Switch H1 (Double Rocker) for 10 seconds, and the indicator light will flash for 3 times quickly when the device is powered on. 3. If the device is successfully bound, the indicator light will flash twice slowly; if it fails, it will stay on for 1s. 4. If the addition fails, please move the switch closer to the hub and try again.
1.When you click the corresponding mode to switch, you need to click the button five times quickly until the gateway prompts “Normal link confirmed” (only supported in some Aqara hubs). 2.The device may be too far away from the hub, or fail to receive mode switching command issued by the hub due to signal interference. 3.If the device is offline, please reset and bind the wireless switch again.
1.When you click the corresponding mode to switch, you need to click the button five times quickly until the gateway prompts “Normal link confirmed” (only supported in some Aqara hubs). 2.The device may be too far away from the hub, or fail to receive mode switching command issued by the hub due to signal interference. 3.If the device is offline, please reset and bind the wireless switch again.
1.When you click the corresponding mode to switch, you need to click the button five times quickly until the gateway prompts “Normal link confirmed” (only supported in some Aqara hubs). 2.The device may be too far away from the hub, or fail to receive mode switching command issued by the hub due to signal interference. 3.If the device is offline, please reset and bind the wireless switch again.
Currently it supports the Aqara Camera Hub G2H, Aqara Hub M1S, Aqara Hub M2, Aqara Air Conditioning Controller P3, Aqara Smart Wall Outlet H1 (USB) and more devices will be supported. Please see https://www.aqara.com/support for more details.
Currently it supports the Aqara Camera Hub G2H, Aqara Hub M1S, Aqara Hub M2, Aqara Air Conditioning Controller P3, Aqara Smart Wall Outlet H1 (USB) and more devices will be supported. Please see https://www.aqara.com/support for more details.
Currently it supports the Aqara Camera Hub G2H, Aqara Hub M1S, Aqara Hub M2, Aqara Air Conditioning Controller P3, Aqara Smart Wall Outlet H1 (USB) and more devices will be supported. Please see https://www.aqara.com/support for more details.
The Aqara Smart Wall Switch can control the lights by controlling the power switch. After pairing with the Aqara Hub, the Aqara Smart Wall Switch can realize remote control, timer control and automation connection with other smart devices.
Aqara Smart Wall Switch can not connect to Wi-Fi directly. The Aqara Smart Wall Switch is a device based on the Zigbee communication protocol. It needs to connect to the Aqara Hub to be controlled by the app.
The Aqara Smart Wall Switch can control the lights by controlling the power switch. After pairing with the Aqara Hub, the Aqara Smart Wall Switch can realize remote control, timer control and automation connection with other smart devices.
First, make sure the power is cut off and there is no current going through the wire. Use the wiring nuts included in the package, wire according to the manual and check whether the wiring is correct. When you finish the above steps, turn on the power and add the Aqara Smart Wall Switch according to the instructions on the app.
Aqara Smart Wall Switch can not connect to Wi-Fi directly. The Aqara Smart Wall Switch is a device based on the Zigbee communication protocol. It needs to connect to the Aqara Hub to be controlled by the app.
If the device is not connected with the network or is offline, long press the button of the Aqara Smart Wall Switch for more than 5 seconds to reset. If the connection between Aqara Smart Wall Switch and the hub is working normally, in order to prevent users from deleting it by mistake, it is required to double press the button and then long press for more than 5 second to finish resetting. After the red indicator light is on for 1 second, it turns blue and flashes fast, which indicates the Aqara Smart Wall Switch has been reset successfully.
First, make sure the power is cut off and there is no current going through the wire. Use the wiring nuts included in the package, wire according to the manual and check whether the wiring is correct. When you finish the above steps, turn on the power and add the Aqara Smart Wall Switch according to the instructions on the app.
If the external network is down, the Aqara Smart Wall Switch can’t be controlled by the Aqara Home App, but the local automation will not be affected. If the power for the Aqara Hub is working properly, the connected automation between the Aqara Smart Wall Switch and other smart devices will work normally too.
If the device is not connected with the network or is offline, long press the button of the Aqara Smart Wall Switch for more than 5 seconds to reset. If the connection between Aqara Smart Wall Switch and the hub is working normally, in order to prevent users from deleting it by mistake, it is required to double press the button and then long press for more than 5 second to finish resetting. After the red indicator light is on for 1 second, it turns blue and flashes fast, which indicates the Aqara Smart Wall Switch has been reset successfully.
The power for the Aqara Smart Wall Switch is set to be off on default when power comes back again after a power outage. The power off memory in the settings of the Aqara Smart Wall Switch normally is off. Users can choose to enable it. If enabled, when power comes back, the Aqara Smart Wall Switch will resume the previous power status from before the last power outage.
If the external network is down, the Aqara Smart Wall Switch can’t be controlled by the Aqara Home App, but the local automation will not be affected. If the power for the Aqara Hub is working properly, the connected automation between the Aqara Smart Wall Switch and other smart devices will work normally too.
For the specific instructions, please refer to the "Effective Range Test” in the manual for detailed instructions. If the hub indicates "normal link confirmed" then it means the smart wall switch and hub are connected effectively. If there is no indication, please move the hub closer to the smart wall switch and try again.
The power for the Aqara Smart Wall Switch is set to be off on default when power comes back again after a power outage. The power off memory in the settings of the Aqara Smart Wall Switch normally is off. Users can choose to enable it. If enabled, when power comes back, the Aqara Smart Wall Switch will resume the previous power status from before the last power outage.
Please check if the Wi-Fi and power to the hub is working normally. If both of them are working normally, please reset the Aqara Smart Wall Switch and connect it to the hub again according to the manual. If it fails to connect, please move the hub closer to the wall switch.
For the specific instructions, please refer to the "Effective Range Test” in the manual for detailed instructions. If the hub indicates "normal link confirmed" then it means the smart wall switch and hub are connected effectively. If there is no indication, please move the hub closer to the smart wall switch and try again.
The choice between the Aqara Smart Wall Switch (No Neutral) and the Aqara Smart Wall Switch (With Neutral) mainly depends on whether there is neutral wire in the electrical box. If there is, it is recommended to choose the Aqara Smart Wall Switch (With Neutral) which will be more stable.
Please check if the Wi-Fi and power to the hub is working normally. If both of them are working normally, please reset the Aqara Smart Wall Switch and connect it to the hub again according to the manual. If it fails to connect, please move the hub closer to the wall switch.
The choice between the Aqara Smart Wall Switch (No Neutral) and the Aqara Smart Wall Switch (With Neutral) mainly depends on whether there is neutral wire in the electrical box. If there is, it is recommended to choose the Aqara Smart Wall Switch (With Neutral) which will be more stable.
Due to design, the Aqara Smart Wall Switch (No Neutral) can’t adjust well to lights of small load. The minimum power of typical load that the Aqara Smart Wall Switch supports is 3W/way (Incandescent) and 5W/way (CFL/LED). If the load for the light is smaller, it will flash occasionally.
The Aqara Smart Wall Switch can control the lights by controlling the power switch. After pairing with the Aqara Hub, the Aqara Smart Wall Switch can realize remote control, timer control and automation connection with other smart devices.
The Aqara Smart Wall Switch can control the lights by controlling the power switch. After pairing with the Aqara Hub, the Aqara Smart Wall Switch can realize remote control, timer control and automation connection with other smart devices.
Aqara Smart Wall Switch can not connect to Wi-Fi directly. The Aqara Smart Wall Switch is a device based on the Zigbee communication protocol. It needs to connect to the Aqara Hub to be controlled by the app.
Aqara Smart Wall Switch can not connect to Wi-Fi directly. The Aqara Smart Wall Switch is a device based on the Zigbee communication protocol. It needs to connect to the Aqara Hub to be controlled by the app.
First, make sure the power is cut off and there is no current going through the wire. Use the wiring nuts included in the package, wire according to the manual and check whether the wiring is correct. When you finish the above steps, turn on the power and add the Aqara Smart Wall Switch according to the instructions on the app.
First, make sure the power is cut off and there is no current going through the wire. Use the wiring nuts included in the package, wire according to the manual and check whether the wiring is correct. When you finish the above steps, turn on the power and add the Aqara Smart Wall Switch according to the instructions on the app.
If the device is not connected with the network or is offline, long press the button of the Aqara Smart Wall Switch for more than 5 seconds to reset. If the connection between Aqara Smart Wall Switch and the hub is working normally, in order to prevent users from deleting it by mistake, it is required to double press the button and then long press for more than 5 second to finish resetting. After the red indicator light is on for 1 second, it turns blue and flashes fast, which indicates the Aqara Smart Wall Switch has been reset successfully.
If the device is not connected with the network or is offline, long press the button of the Aqara Smart Wall Switch for more than 5 seconds to reset. If the connection between Aqara Smart Wall Switch and the hub is working normally, in order to prevent users from deleting it by mistake, it is required to double press the button and then long press for more than 5 second to finish resetting. After the red indicator light is on for 1 second, it turns blue and flashes fast, which indicates the Aqara Smart Wall Switch has been reset successfully.
If the external network is down, the Aqara Smart Wall Switch can’t be controlled by the Aqara Home App, but the local automation will not be affected. If the power for the Aqara Hub is working properly, the connected automation between the Aqara Smart Wall Switch and other smart devices will work normally too.
If the external network is down, the Aqara Smart Wall Switch can’t be controlled by the Aqara Home App, but the local automation will not be affected. If the power for the Aqara Hub is working properly, the connected automation between the Aqara Smart Wall Switch and other smart devices will work normally too.
The power for the Aqara Smart Wall Switch is set to be off on default when power comes back again after a power outage. The power off memory in the settings of the Aqara Smart Wall Switch normally is off. Users can choose to enable it. If enabled, when power comes back, the Aqara Smart Wall Switch will resume the previous power status from before the last power outage.
The power for the Aqara Smart Wall Switch is set to be off on default when power comes back again after a power outage. The power off memory in the settings of the Aqara Smart Wall Switch normally is off. Users can choose to enable it. If enabled, when power comes back, the Aqara Smart Wall Switch will resume the previous power status from before the last power outage.
For the specific instructions, please refer to the "Effective Range Test” in the manual for detailed instructions. If the hub indicates "normal link confirmed" then it means the smart wall switch and hub are connected effectively. If there is no indication, please move the hub closer to the smart wall switch and try again.
For the specific instructions, please refer to the "Effective Range Test” in the manual for detailed instructions. If the hub indicates "normal link confirmed" then it means the smart wall switch and hub are connected effectively. If there is no indication, please move the hub closer to the smart wall switch and try again.
Please check if the Wi-Fi and power to the hub is working normally. If both of them are working normally, please reset the Aqara Smart Wall Switch and connect it to the hub again according to the manual. If it fails to connect, please move the hub closer to the wall switch.
Please check if the Wi-Fi and power to the hub is working normally. If both of them are working normally, please reset the Aqara Smart Wall Switch and connect it to the hub again according to the manual. If it fails to connect, please move the hub closer to the wall switch.
The choice between the Aqara Smart Wall Switch (No Neutral) and the Aqara Smart Wall Switch (With Neutral) mainly depends on whether there is neutral wire in the electrical box. If there is, it is recommended to choose the Aqara Smart Wall Switch (With Neutral) which will be more stable.
The choice between the Aqara Smart Wall Switch (No Neutral) and the Aqara Smart Wall Switch (With Neutral) mainly depends on whether there is neutral wire in the electrical box. If there is, it is recommended to choose the Aqara Smart Wall Switch (With Neutral) which will be more stable.
It can be installed in the wall box or the ceiling or the ceiling light to control the lights; it can also be installed in the cassette of the ordinary wall socket to transform the socket into a smart wall socket; or it can be installed in exhaust fan, electric water heater and other strong electrical device with enough internal space and qualified structure and suitable electrical performance. The requirements for electrical knowledge and hands-on skills are high, so professionals are required to install it.
It can be installed in the wall box or the ceiling or the ceiling light to control the lights; it can also be installed in the cassette of the ordinary wall socket to transform the socket into a smart wall socket; or it can be installed in exhaust fan, electric water heater and other strong electrical device with enough internal space and qualified structure and suitable electrical performance. The requirements for electrical knowledge and hands-on skills are high, so professionals are required to install it.
Both are relay control modules with the same main functions, but the former needs to be connected with the neutral line and the live line, and the latter only needs to be connected with the live line to supply power. You need to choose one according to your home wiring.
Both are relay control modules with the same main functions, but the former needs to be connected with the neutral line and the live line, and the latter only needs to be connected with the live line to supply power. You need to choose one according to your home wiring.
There are 5 wiring holes on the back, which are L1, S0, S1, L, and N. Among them, the load line, such as lights or socket, connect to L1, the live line connects to L, and the neutral line connects to N.
There are three connection methods for S0 and S1: 1. Connect them to the two ends of the external switch respectively; 2. Connect S0 to one end of the external switch; S1 is idle. The other end is connected to the fire line; 3. If there is no external switch, you don't need to connect it. The first two connection methods can realize the control of the Single Switch Module T1 by the external switch.
There are 5 wiring holes on the back, which are L1, S0, S1, L, and N. Among them, the load line, such as lights or socket, connect to L1, the live line connects to L, and the neutral line connects to N.
There are three connection methods for S0 and S1: 1. Connect them to the two ends of the external switch respectively; 2. Connect S0 to one end of the external switch; S1 is idle. The other end is connected to the fire line; 3. If there is no external switch, you don't need to connect it. The first two connection methods can realize the control of the Single Switch Module T1 by the external switch.
In the case of wrong wiring, the Single Switch Module T1 may burn out or fail to work. Please strictly follow the instructions for wiring, or ask a professional electrician to install it!
In the case of wrong wiring, the Single Switch Module T1 may burn out or fail to work. Please strictly follow the instructions for wiring, or ask a professional electrician to install it!
1. It can be considered to arrange the wires across the cassette and cut the over-length wires in the cassette to a suitable length to get more space.
2. It can be considered to place it in the ceiling or the ceiling light, but it needs to stay as far away as possible from the Luminous and heating parts of the light.
3. It can be considered to expand the cassette depth by professionals.
1. It can be considered to arrange the wires across the cassette and cut the over-length wires in the cassette to a suitable length to get more space.
2. It can be considered to place it in the ceiling or the ceiling light, but it needs to stay as far away as possible from the Luminous and heating parts of the light.
3. It can be considered to expand the cassette depth by professionals.
It can be connected with rocker switch (bistable) or rebound switch (monostable). After it is connected with the external switch, you need to set it on the app. The default connection is the rocker switch.
It can be connected with rocker switch (bistable) or rebound switch (monostable). After it is connected with the external switch, you need to set it on the app. The default connection is the rocker switch.
When the control module is installed in the pattress, it is recommended to paste the antenna on the side wall of the plastic cassette and keep it parallel to the wall; if the switch panel bracket is made of plastic, it is recommended that the antenna is no more than 10mm away from the wall; if the switch panel bracket is made of metal, then it is recommended that the antenna should be more than 15mm away from the wall (metal bracket); in addition, the antenna should be as far away as possible from the main unit of the control module and the AC cable (the recommended distance is more than 15mm). If it is installed in a metal pattress, it is recommended to install the antenna on the plastic switch panel, but it needs sufficient space on the panel. If it is installed on the ceiling or inside the light, the antenna should avoid to be pasted on the metal, and also should avoid too much shielding.
When the control module is installed in the pattress, it is recommended to paste the antenna on the side wall of the plastic cassette and keep it parallel to the wall; if the switch panel bracket is made of plastic, it is recommended that the antenna is no more than 10mm away from the wall; if the switch panel bracket is made of metal, then it is recommended that the antenna should be more than 15mm away from the wall (metal bracket); in addition, the antenna should be as far away as possible from the main unit of the control module and the AC cable (the recommended distance is more than 15mm). If it is installed in a metal pattress, it is recommended to install the antenna on the plastic switch panel, but it needs sufficient space on the panel. If it is installed on the ceiling or inside the light, the antenna should avoid to be pasted on the metal, and also should avoid too much shielding.
There are three ways to enter the networking status: 1. When the Single Switch Module T1 does not connect to the network, it will automatically enter the networking status after it powers on, and it should maintain the status for 30 seconds; 2. You can press the button on the Single Switch Module T1 for 8 seconds to enter the networking status, and it should maintain the status for 30 seconds; 3. It can be turned on and off 5 times through an external switch to make the Single Switch Module T1 enter the networking status, and it should maintain the status for 30 seconds.
There are three ways to enter the networking status: 1. When the Single Switch Module T1 does not connect to the network, it will automatically enter the networking status after it powers on, and it should maintain the status for 30 seconds; 2. You can press the button on the Single Switch Module T1 for 8 seconds to enter the networking status, and it should maintain the status for 30 seconds; 3. It can be turned on and off 5 times through an external switch to make the Single Switch Module T1 enter the networking status, and it should maintain the status for 30 seconds.
Single Switch Module T1 (With Neutral) must connect to the compatible hub to realize functions such as interaction and remote control. After the wiring is completed, please open the app client side, click Add Sub Device, select the corresponding single switch module in the options, and follow the prompts.
Single Switch Module T1 (With Neutral) must connect to the compatible hub to realize functions such as interaction and remote control. After the wiring is completed, please open the app client side, click Add Sub Device, select the corresponding single switch module in the options, and follow the prompts.
The effective distance between the both devices is 7 to 10 meters with a wall between them, which may depend on material and thickness of the wall, and abmient environment conditions. If more walls are between the both devices, we recommend to shorten the distance.
The effective distance between the both devices is 7 to 10 meters with a wall between them, which may depend on material and thickness of the wall, and abmient environment conditions. If more walls are between the both devices, we recommend to shorten the distance.
First, by using Single Switch Module T1 (With Neutral) in combination with a wireless switch, it is very easy to realize double control / multiple control. The wireless switch can be placed at most positions of your home to coordinately control the Single Switch Module T1 (With Neutral);
If the traditional double-control switch has been installed, Single Switch Module T1 (With Neutral) can be placed in the controlled device or in the cassette near the device . The original switch connects to from the line end of the load wire to S0 wiring hole, S1 is not connected, L1 / L wiring hole is connected normally, and the original double control line can be maintained to realize double control.
First, by using Single Switch Module T1 (With Neutral) in combination with a wireless switch, it is very easy to realize double control / multiple control. The wireless switch can be placed at most positions of your home to coordinately control the Single Switch Module T1 (With Neutral);
If the traditional double-control switch has been installed, Single Switch Module T1 (With Neutral) can be placed in the controlled device or in the cassette near the device . The original switch connects to from the line end of the load wire to S0 wiring hole, S1 is not connected, L1 / L wiring hole is connected normally, and the original double control line can be maintained to realize double control.
The Aqara Cube can be operated in 7 ways: Flip 90°, Flip 180°, Shake, Rotate, Tap Twice, Push, and Motion detected after a minute. You can set up automations in the Aqara Home app that will allow you to control all of your smart devices. For example: Shaking to control the night light on the Aqara Hub; Flip 90° to turn on/off the Aqara Smart Plug; Flip 180° to control the Aqara Smart Wall Switch.
The Aqara Cube can be operated in 7 ways: Flip 90°, Flip 180°, Shake, Rotate, Tap Twice, Push, and Motion detected after a minute. You can set up automations in the Aqara Home app that will allow you to control all of your smart devices. For example: Shaking to control the night light on the Aqara Hub; Flip 90° to turn on/off the Aqara Smart Plug; Flip 180° to control the Aqara Smart Wall Switch.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the cube is reset successfully, and the LED indicator is blinking as expected. 4. Keep the cube as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the cube is reset successfully, and the LED indicator is blinking as expected. 4. Keep the cube as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the sensor itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
Possible reasons: 1. The accessory is too far away from the hub. Please try to install the accessory closer to the hub. 2. Low battery or dead battery. Please replace the battery. 3. The accessory is installed on a metal surface and the signal is interfered with. Please avoid metal surfaces.
Possible reasons: 1. The accessory is too far away from the hub. Please try to install the accessory closer to the hub. 2. Low battery or dead battery. Please replace the battery. 3. The accessory is installed on a metal surface and the signal is interfered with. Please avoid metal surfaces.
The Aqara Cube cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Cube to the hub.
The Aqara Cube cannot be connected to the mobile phone directly. An Aqara Hub is required, please connect the Aqara Hub with the mobile phone, and then connect the Aqara Cube to the hub.
Please place the Aqara Cube on a flat surface to operate. If you operate it on a soft surface, such as a sofa or pillow, the Aqara Cube might not respond normally.
Please place the Aqara Cube on a flat surface to operate. If you operate it on a soft surface, such as a sofa or pillow, the Aqara Cube might not respond normally.
If the external network is down, the app control function for the Aqara Cube will no longer be available. But the local control automation for the Aqara Cube will not be affected and its connection with other smart devices will function normally.
If the external network is down, the app control function for the Aqara Cube will no longer be available. But the local control automation for the Aqara Cube will not be affected and its connection with other smart devices will function normally.
You can rename the Aqara Cubes to distinguish them. After the Aqara Cube connects to the Aqara Hub successfully, you will be given an option to rename it. You can also rename it on the settings page for the Aqara Cube.
You can rename the Aqara Cubes to distinguish them. After the Aqara Cube connects to the Aqara Hub successfully, you will be given an option to rename it. You can also rename it on the settings page for the Aqara Cube.
Please follow the steps below: Aqara Home App>Accessory>"+">select Aqara Cube>select hub> Open the lid with the metal strip which comes with the package, long press the reset button for 5 seconds until the LED indicator blinks 2 times.(For the first time using, just shake the Aqara Cube hard).
Please follow the steps below: Aqara Home App>Accessory>"+">select Aqara Cube>select hub> Open the lid with the metal strip which comes with the package, long press the reset button for 5 seconds until the LED indicator blinks 2 times.(For the first time using, just shake the Aqara Cube hard).
No, Apple Home does not have an interface that supports the Aqara Cube control operations, so the Aqara Cube cannot connect to HomeKit. Please download the Aqara Home app for use.
No, Apple Home does not have an interface that supports the Aqara Cube control operations, so the Aqara Cube cannot connect to HomeKit. Please download the Aqara Home app for use.
The Aqara Wireless Mini Switch can either be attached to the wall or placed on a table. Installation on a metal door is not recommended because metal surfaces affect the signal. When being used as a doorbell, the wireless switch can be installed on the wall next to a metal door. Please refer to the quick start guide for more details.
The indoor environment varies, and maximum signal strength between the Aqara Hub and the Aqara Wireless Mini Switch is different. There should not be more than two walls between them.
1. Check to see if the hub's firmware version is up to date. 2. Check if the hub is already in the pairing mode. 3. Check if the switch is reset successfully, and the LED indicator is blinking as expected. 4. Keep the switch as close as possible to the hub and keep trying. 5. Try with another child device to see if there is something wrong with the switch itself. 6. Try with another hub and see if there is something wrong with the previous hub. 7. Please be aware that we can add no more than 32 child devices to a hub at the same time.
Possible reasons: 1. The accessory is too far from the hub. Please install it closer to the hub. 2. The battery is dead. Please replace the battery. 3. The accessory has been installed on metal and the signal has been interfered with. The accessory should be installed away from metal.
1. Single press the reset button of the switch, the hub will prompt with the voice message "normal link confirmed" which means the connection between the switch and the hub is normal. If the hub gives no response, please move the switch closer to the hub and try again. If the hub remains silent, the switch might have been removed from the hub or run out of power. Please follow the instructions to add the switch or replace the battery. 2. Single-click/double-click/long press the Aqara Wireless Mini Switch several times, enter the homepage of the switch in app, then check the log . The switch is working properly if the corresponding event has been updated in the log.
1. Press and hold the reset button on the device for 5 seconds. The indicator will flash 3 times before resetting to factory settings. 2. If a device needs to be paired with another Aqara Hub, it will need to be reset before the new pairing will succeed.
1. Use a coin to to rotate the battery cover counter clockwise until the cover loosens. 2. Remove the existing battery. Place the new CR2032 battery in the battery compartment and make sure that the positive side of the battery faces upwards. 3. Align the battery cover with the bottom of the Aqara Temperature and Humidity Sensor. Use a coin to rotate the battery cover clockwise until you hear a click. The battery cover is successfully replaced.
You can use your mobile phone to turn on/off the home appliances connected with the Aqara Smart Plug. Also, you can set a timer for the home appliances to automatically turn on/off anytime and program automations and scenes to trigger based on Aqara sensors.
You can use your mobile phone to turn on/off the home appliances connected with the Aqara Smart Plug. Also, you can set a timer for the home appliances to automatically turn on/off anytime and program automations and scenes to trigger based on Aqara sensors.
First, ensure that the Aqara Hub works normally. Then, open the Aqara Home app, select the “+” in the upper right corner. Enter "Accessories" page and choose the Aqara Smart Plug, then follow the instructions in the app.
First, ensure that the Aqara Hub works normally. Then, open the Aqara Home app, select the “+” in the upper right corner. Enter "Accessories" page and choose the Aqara Smart Plug, then follow the instructions in the app.
Long press the reset button for more than 5 seconds. When the red indicator light blinks for 1 second and starts a quick blue flashing, the Aqara Smart Plug has been successfully reset.
Long press the reset button for more than 5 seconds. When the red indicator light blinks for 1 second and starts a quick blue flashing, the Aqara Smart Plug has been successfully reset.
If the external network is down, the app control function for Aqara Smart Plug will no longer be available. But the local control for the Aqara Smart Plug will not be affected and its connection with other smart devices will function normally.
If the external network is down, the app control function for Aqara Smart Plug will no longer be available. But the local control for the Aqara Smart Plug will not be affected and its connection with other smart devices will function normally.
The Aqara Smart Plug has a built-in socket protector to prevent accidental electrocution. The maximum load power of the Aqara Smart Plug is 1875W. When the connected appliance exceeds the maximum load power, the Aqara Smart Plug will automatically cut off the power to avoid any danger.
The Aqara Smart Plug has a built-in socket protector to prevent accidental electrocution. The maximum load power of the Aqara Smart Plug is 1875W. When the connected appliance exceeds the maximum load power, the Aqara Smart Plug will automatically cut off the power to avoid any danger.
For safety reasons, when the Aqara Smart Plug powers off, the Aqara Smart Plug does not save settings. However, there is a “power-off memory” option in the app. By choosing this option, the Aqara Smart Plug settings will be restored to their previous status.
For safety reasons, when the Aqara Smart Plug powers off, the Aqara Smart Plug does not save settings. However, there is a “power-off memory” option in the app. By choosing this option, the Aqara Smart Plug settings will be restored to their previous status.
The maximum load power for the Aqara Smart Plug is 1875W. The maximum load voltage and current are 100-125V and 15A, respectively. Appliances with load power, voltage and current that do not exceed these maximums can be used with the Aqara Smart Plug.
The maximum load power for the Aqara Smart Plug is 1875W. The maximum load voltage and current are 100-125V and 15A, respectively. Appliances with load power, voltage and current that do not exceed these maximums can be used with the Aqara Smart Plug.
For specific instructions, please refer to the "Effective Range Test” instructions in the operating manual. If the hub indicates "normal link confirmed" then it means the smart plug and hub are connected effectively. If there is no voice prompt, please move the smart plug closer to the hub and try again.
For specific instructions, please refer to the "Effective Range Test” instructions in the operating manual. If the hub indicates "normal link confirmed" then it means the smart plug and hub are connected effectively. If there is no voice prompt, please move the smart plug closer to the hub and try again.
Please check if the Wi-Fi network and the power supply of the hub work properly. If they do work normally, please reset the Aqara Smart Plug and reconnect the smart plug according to instructions. If the connection is unsuccessful, please move the plug closer to the hub and try again.
Please check if the Wi-Fi network and the power supply of the hub work properly. If they do work normally, please reset the Aqara Smart Plug and reconnect the smart plug according to instructions. If the connection is unsuccessful, please move the plug closer to the hub and try again.
You can use your mobile phone to turn on/off the home appliances connected with the Aqara Smart Plug. Also, you can set a timer for the home appliances to automatically turn on/off anytime and program automations and scenes to trigger based on Aqara sensors.
You can use your mobile phone to turn on/off the home appliances connected with the Aqara Smart Plug. Also, you can set a timer for the home appliances to automatically turn on/off anytime and program automations and scenes to trigger based on Aqara sensors.
First, ensure that the Aqara Hub works normally. Then, open the Aqara Home app, select the “+” in the upper right corner. Enter "Accessories" page and choose the Aqara Smart Plug, then follow the instructions in the app.
First, ensure that the Aqara Hub works normally. Then, open the Aqara Home app, select the “+” in the upper right corner. Enter "Accessories" page and choose the Aqara Smart Plug, then follow the instructions in the app.
Long press the reset button for more than 5 seconds. When the red indicator light blinks for 1 second and starts a quick blue flashing, the Aqara Smart Plug has been successfully reset.
Long press the reset button for more than 5 seconds. When the red indicator light blinks for 1 second and starts a quick blue flashing, the Aqara Smart Plug has been successfully reset.
If the external network is down, the app control function for Aqara Smart Plug will no longer be available. But the local control for the Aqara Smart Plug will not be affected and its connection with other smart devices will function normally.
If the external network is down, the app control function for Aqara Smart Plug will no longer be available. But the local control for the Aqara Smart Plug will not be affected and its connection with other smart devices will function normally.
The Aqara Smart Plug has a built-in socket protector to prevent accidental electrocution. The maximum load power of the Aqara Smart Plug is 2300W. When the connected appliance exceeds the maximum load power, the Aqara Smart Plug will automatically cut off the power to avoid any danger.
The Aqara Smart Plug has a built-in socket protector to prevent accidental electrocution. The maximum load power of the Aqara Smart Plug is 2300W. When the connected appliance exceeds the maximum load power, the Aqara Smart Plug will automatically cut off the power to avoid any danger.
For safety reasons, when the Aqara Smart Plug powers off, the Aqara Smart Plug does not save settings. However, there is a “power-off memory” option in the app. By choosing this option, the Aqara Smart Plug settings will be restored to their previous status.
For safety reasons, when the Aqara Smart Plug powers off, the Aqara Smart Plug does not save settings. However, there is a “power-off memory” option in the app. By choosing this option, the Aqara Smart Plug settings will be restored to their previous status.
The maximum load power for the Aqara Smart Plug is 2300W. The maximum load voltage and current are 250V~ and 10A, respectively. Appliances with load power, voltage and current that do not exceed these maximums can be used with the Aqara Smart Plug.
The maximum load power for the Aqara Smart Plug is 2300W. The maximum load voltage and current are 250V~ and 10A, respectively. Appliances with load power, voltage and current that do not exceed these maximums can be used with the Aqara Smart Plug.
For specific instructions, please refer to the "Effective Range Test” instructions in the operating manual. If the hub indicates "normal link confirmed" then it means the smart plug and hub are connected effectively. If there is no voice prompt, please move the smart plug closer to the hub and try again.
For specific instructions, please refer to the "Effective Range Test” instructions in the operating manual. If the hub indicates "normal link confirmed" then it means the smart plug and hub are connected effectively. If there is no voice prompt, please move the smart plug closer to the hub and try again.
Please check if the Wi-Fi network and the power supply of the hub work properly. If they do work normally, please reset the Aqara Smart Plug and reconnect the smart plug according to instructions. If the connection is unsuccessful, please move the plug closer to the hub and try again.
Please check if the Wi-Fi network and the power supply of the hub work properly. If they do work normally, please reset the Aqara Smart Plug and reconnect the smart plug according to instructions. If the connection is unsuccessful, please move the plug closer to the hub and try again.
Both are smart wall switches with the same main functions. However, the former needs to be connected to the neutral wire and the live wire, and the latter only needs to be connected to the live wire for the power supply. You can choose based on the lighting wiring design of your home.
The wall switch needs to be connected to the wire. The most important function is to remotely and intelligently control the power of the connected circuit. To transform the ordinary electric light into a smart light, the wall switch is required; the wireless switch is a controller that can control wall switches and other devices via the app but cannot directly control non-smart lights independently.
Lights such as smart lights, color-changing lights, gradient lights, remote control lights and light strips, and high-power appliances such as bathroom heater are not supported.
Normally, the live wire is red, the neutral wire is black or blue, and the lamp load wire is generally green or yellow. A test by a professional electrician with professional tools such as electric pens should be performed before installation.
In the case of an incorrect connection, the wall switch may not work normally, and the switch may burn out in severe cases. Please strictly follow the wiring instructions, or hire a professional electrician for installation.
①Since the Smart Wall Switch (With Neutral, Single/Double Rocker) is connected to the neutral wire and the live wire, there is no minimum load requirement. ②For the Smart Wall Switch (No Neutral, Single/Double Rocker), normally each load can support 3W energy-saving lamps, LED lamps or 16W fluorescent lamps at least. However, for some lamps of small brands or lamps with poor materials, due to the internal circuit design of the lamps, even if the power is greater than the above requirements, it may cause abnormal phenomena such as lamp flicker and switch crashes. Please choose the lamp carefully. *Please note: If it is an old-fashioned tube lamp with a starter, please replace the electronic starter.
When the power of the lamp connected to the Smart Wall Switch H1 EU (No Neutral Version) is lower than the minimum power requirement, sometimes it will flicker when the switch is turned off. In addition, lamps of mainstream brand works better with Smart Wall Switch H1 EU (No Neutral Version) and some lamps of small brands or copycat manufacturers may flicker or cause the switch to crash due to the poor internal circuit design and material problems. Please choose the lamps properly.
Firstly, by using the Smart Wall Switch H1 EU with the Wireless Remote Switch, dual-/multi-control functions can be used very easily. The Wireless Remote Switch can be put in most places in your home to control the Smart Wall Switch via smart automation; secondly, if the original switches in your home are dual-controllers and you only replace one of the switches with the Smart Wall Switch H1 EU, please keep the other ordinary switch short-circuited and replace it with a wireless switch, otherwise, the Zigbee communication module of Smart Wall Switch can not be powered when the other switch is powered off and the switch cannot be controlled intelligently.
Both are smart wall switches with the same main functions. However, the former needs to be connected to the neutral wire and the live wire, and the latter only needs to be connected to the live wire for the power supply. You can choose based on the lighting wiring design of your home.
The wall switch needs to be connected to the wire. The most important function is to remotely and intelligently control the power of the connected circuit. To transform the ordinary electric light into a smart light, the wall switch is required; the wireless switch is a controller that can control wall switches and other devices via the app but cannot directly control non-smart lights independently.
Lights such as smart lights, color-changing lights, gradient lights, remote control lights and light strips, and high-power appliances such as bathroom heater are not supported.
Normally, the live wire is red, the neutral wire is black or blue, and the lamp load wire is generally green or yellow. A test by a professional electrician with professional tools such as electric pens should be performed before installation.
In the case of an incorrect connection, the wall switch may not work normally, and the switch may burn out in severe cases. Please strictly follow the wiring instructions, or hire a professional electrician for installation.
①Since the Smart Wall Switch (With Neutral, Single/Double Rocker) is connected to the neutral wire and the live wire, there is no minimum load requirement. ②For the Smart Wall Switch (No Neutral, Single/Double Rocker), normally each load can support 3W energy-saving lamps, LED lamps or 16W fluorescent lamps at least. However, for some lamps of small brands or lamps with poor materials, due to the internal circuit design of the lamps, even if the power is greater than the above requirements, it may cause abnormal phenomena such as lamp flicker and switch crashes. Please choose the lamp carefully. *Please note: If it is an old-fashioned tube lamp with a starter, please replace the electronic starter.
When the power of the lamp connected to the Smart Wall Switch H1 EU (No Neutral Version) is lower than the minimum power requirement, sometimes it will flicker when the switch is turned off. In addition, lamps of mainstream brand works better with Smart Wall Switch H1 EU (No Neutral Version) and some lamps of small brands or copycat manufacturers may flicker or cause the switch to crash due to the poor internal circuit design and material problems. Please choose the lamps properly.
Firstly, by using the Smart Wall Switch H1 EU with the Wireless Remote Switch, dual-/multi-control functions can be used very easily. The Wireless Remote Switch can be put in most places in your home to control the Smart Wall Switch via smart automation; secondly, if the original switches in your home are dual-controllers and you only replace one of the switches with the Smart Wall Switch H1 EU, please keep the other ordinary switch short-circuited and replace it with a wireless switch, otherwise, the Zigbee communication module of Smart Wall Switch can not be powered when the other switch is powered off and the switch cannot be controlled intelligently.
Please long-press the Stop button "||" on the control box for 5 seconds until the blue indicator light goes on and then release it. When you hear the motor short beeps three times, the motor will return to normal status after it turns forward and backward once.
When the motor runs continuously for about 4 minutes, the motor will stop running and enter the overheating protection state. When the temperature returns to the appropriate level, it will work normally again (about 10-30 minutes to recover).
When the motor runs continuously for about 4 minutes, the motor will stop running and enter the overheating protection state. When the temperature returns to the appropriate level, it will work normally again (about 10-30 minutes to recover).
When the route of the motor is not set completely, the motor cannot be controlled through the app, and the homepage of the app will not display the control buttons. You need to complete the route settings according to the guideline, and then enter the app to control it.
The "dimming control" feature is suitable for Venetian blinds, Shangri-La blinds, gauze curtain, etc. You can use this feature to control the blade inclination angle of the Venetian blinds and Shangri-La blinds or set the overlapping area of two layers of gauze curtain to adjust indoor lighting.
1. The equivalent capacity of a standard single battery out of the doorbell factory is about 2900 mAh. When you replace it with a new battery, please choose the battery with a capacity not less than 2900 mAh. 2. If connected with HomeKit, the doorbell will record video if it is triggered and there’s motion detected until the motion ends, which may consume more power and shorten the battery life compared to using the doorbell in Aqara Home only. 3. If the loitering detection interval is configured too short, the doorbell may be frequently triggered, which may shorten the battery life. 4. Battery life can be shortened by using new and old batteries together, using other non-LR6 batteries or non-1.5V batteries. 5. If the doorbell is far away from the repeater (more than Max. 5 meters), or there is too much wireless interference in the surroundings, the doorbell will need to increase the transmission power for communication, which will result in the higher power consumption and shorten the battery life. 6. In the Power Saving Mode, the PIR detection function is turned off, and the doorbell can only be triggered by pressing the bell, remotely viewing video in the app, etc., which will greatly extend the doorbell life.
1. There might be factors in the surroundings of the doorbell causing the false-triggering of PIR (e.g. thermal disturbances due to big gaps of temperature within the detection range, such as hot air blowing continuously). In this case, please lower the sensitivity or temporarily switch to the Power Saving Mode (PIR function will be turned off.). 2. If the loitering detection interval is too long, the person detected may have left out of the monitoring field when the video recording starts. In this case, please shorten the detection interval.
1. The doorbell can use AA batteries or rechargeable lithium batteries with 1.5V discharge voltage. If NiMH batteries with 1.2V output voltage are used, the electricity statistics will be inaccurate. LR6 alkaline AA batteries are recommended. 2. It is recommended to replace 6 new batteries of the same model at a time. If new and old batteries or different batteries are mixed to use, the battery life will be shortened.
1. Check whether the Power Saving Mode is enabled. If enabled, the video recording can only be triggered by pressing the doorbell or remotely viewing video in the app. PIR can work if switched to the normal mode. 2. Check whether the video recording of loitering detection is turned on. 3. Check whether the loitering detection interval is too long.
Please check whether the distance between the doorbell and the repeater is out of the allowable range, or other Wi-Fi co-frequency interference sources are surrounded, if yes, you can improve the connection by adjusting the position of the repeater or modifying the Wi-Fi channel.
Please ensure that the indicator light switch is turned off. If the doorbell is connected to HomeKit, please turn off the indicator light switch in Apple "Home" app to ensure the synchronization.
2.4 GHz Wi-Fi protocol can be applied between the doorbell and the repeater, and between repeater and the router. The doorbell cannot bind with other child devices directly. To work with other Aqara child devices, an Aqara hub is required.
The screws on the back plate are designed to be immovable to avoid the screws falling off and missing during disassembly of the doorbell. Do not pull out the screw forcibly.
Although the doorbell does not have the hub function, the localization of some doorbell functions can still be realized, such as playing a customized ringtone on the repeater after pressing the doorbell.
1. The face recognition function is turned off by default. You can open the device settings page - More Settings - Detection - Face Recognition, turn the function on and set the relevant parameters. 2. The sensitivity of face recognition is medium by default. If it cannot detect any face even if the function is enabled, please adjust to the high sensitivity. 3. Please check whether the light surrounding the doorbell is good. Face recognition ratio can be lowered under backlight, dim light. In addition, it can be affected by infrared night vision, starting image distortion calibration.
The face recognition has two functions of face capture and face matching, both of which are performed locally on the device. However, to display and mark the face, it needs to connect to the cloud server. When the doorbell is disconnected from the router, it will not affect the face capture and matching, nor affect the local execution of automations related to face recognition. However, the newly captured face image after the doorbell disconnected from the router cannot be displayed on the app.
It is the ambient temperature of the doorbell detected by the high and low temperature alarm. It will alarm before the battery fails due to the impact caused by ambient temperature.
The doorbell relies on the Wi-Fi transmitted by the repeater for connection, and has one-to-one binding configuration with the repeater before leaving the factory. User cannot unbind the doorbell and the repeater.
PIR detection sensitivity is divided into high and low levels. When moving horizontally (90° to the PIR detection direction), PIR can detect about 4 meters with high sensitivity, and about 2 meters with low sensitivity. When moving vertically (parallel to the PIR detection direction), the detection distance will be shortened. PIR horizontal detection angle is 120°, and vertical detection angle is 80°
You can quickly press the button on the top of the camera three times to initiate ZigBee end device connection. G2H Pro support ZigBee 3.0 protocol and can connect 128 end devices at most.
You can scan the QR code generated by Aqara Home app to connect to internet. After the camera is powered on, please open the app and connect the device to 2.4GHz Wi-Fi, according to the voice prompt. Then, the QR code is generated, and you can scan the QR code through the G2H Pro lens for the network connection.
It supports 2.4GHz IEEE902.11b/g/n Wi-Fi protocol. And it doesn’t support 5GHz Wi-Fi. When connecting the mixing frequency router, it is recommended to separate 2.4GHz and 5GHz Wi-Fi to avoid abnormal connection.
Please check the distance between camera and router, and make sure the Wi-Fi signal is strong enough. If Wi-Fi connecting abnormally, please use Wi-Fi signal amplifier or mobile router to ensure that the device can receive Wi-Fi signals well. Please make sure connecting to 2.4GHz Wi-Fi. Please check if the Wi-Fi SSID or Wi-Fi PWD is correct.
It will take at least 18GB to store one day’s video. Generally, the TF card with 512GB capacity is expected to be stored for 4 weeks, totaling 28 days.
It supports the TF card with CLASS 4 above and format of FAT32. The capacity is 512GB at most. However, We suggest you use the TF card with CLASS 10 above.
It supports magnetic suction and flat installation. You can use 3M glue in the accessories to paste the iron sheet on the non-magnetic material surface, or use fastening screws to fix the iron sheet on the non-magnetic material surface, and then fix the camera.
After the gesture recognition is enabled, it will consume more hardware computing resources, so the face, human shape and pet recognition and other automations related to PTZ are not available. If you disable gesture recognition, other AI functions are available.
Gesture recognition function can be used as the execution condition of automatic control. It can achieve the linkage control of accessory by making a specified static gesture in front of the camera. It is the behavior initiated by the user, and it is not reported as an alarm event or recorded video.
1.Face recognition can be used as the condition of family alert or automatic execution to realize the functions of reporting alarm information and triggering execution automation when detecting unfamiliar or marked faces. 2.Using face recognition for the first time, the Aqara Home APP will guide users to add and synchronize face information to the camera. Face information is stored in the cloud server in the unit of family. Users can synchronize face information to multiple G3 cameras to realize batch operation, and can also add and import faces in the app's setting option. Users can delete face information on their own initiative, and all uploaded face information will be cleared after reset.
The related processes of AI functions(including face, human shape, gesture and pet recognition) will be stopped to ensure the upgrade speed and performance, so the above AI functions are disabled until the upgrade is completed.
Gesture, face, human and pet recognition algorithms all rely on image color information. In night vision mode, the video is gray image, which will affect the effect of AI recognition. It is recommended to experience them only in color mode.
Aqara Camera Hub G3 applies the variable bitrate technology to ensure the 2K Full HD video under various working conditions, and the maximal bitrate is 3.5Mbps when the camera is rotating. To ensure smooth remote viewing, the uplink and downlink bandwidth are required to be higher than that bitrate.
The manual adjustment to the position of the PTZ in the power-on state will lead to the position memory disturbance of the camera. The PTZ can be rotated to the limit position after clicking the one-button PTZ calibration in the Settings - PTZ Settings.
The minimum screen size of the code scanning terminal (such as mobile phone and pad) supported by the camera is 4.7 inches, with the name and password of WLAN of up to 32 ASCII characters (numbers, letters, special symbols), and the best code scanning distance between the QR code and the camera is 8-20cm.
1. The camera supports 128GB MicroSD card and supports the exFat and FAT32 formats 2. Yes. After the device connects to the network successfully, the videos to be saved on the MicroSD card can still be recorded in case of any network disconnection, but these videos saved on the MicroSD card cannot be viewed remotely via app.
1.The associated events label mean that the local video recorded by camera can be marked by different events. For example, if the door and window sensor is enabled or the camera detects any motion, the camera will mark the time and location of this event in the video footage saved in the MicroSD card for further retrieve. 2.Configuration path: “Settings” - “More Settings” - “Alert Setting”, select “Trigger Device” - “Color” - “Save” of the associated events.
There is no limit on the number of connected clients, however, it is recommended that no more than 4 users watch videos simultaneously. The more apps connected, the more processor resource consumed (too many users connected will cause real-time screen lag and delay).
After adding the device to the Apple Home APP, a HomePod or Apple TV (tvOS 11.0 or above) or an iPad (iOS 12.0 or above) that has been set up as the household pivot is required to achieve remote control. Refer to the prompts of Apple Home APP for specific operation.
The Aqara Camera Hub G3 has reserved a standard 1/4" nut hole at the bottom for connecting to the brackets with 1/4" nut, so users can choose the installing brackets recommended by Aqara or other applicable brackets for wall installation or ceiling installation of the camera through the above-mentioned connection method.
Enter the App, click the upper right corner "Settings" - “More Settings” - “Camera Settings” - “Video Settings” - “Installation Methods”, select "Place Upside Down", and the PTZ control and video display will work properly.
The camera supports 2.4/5GHz dual-band Wi-Fi network, and the Wi-Fi networks with WEP, WPA/WPA2, WPA3, WPA-PSK/WPA2-PSK security and encryption mechanism.
Before using the infrared remote control function, the electric appliances to be controlled should be added, then the APP is used as the remote controller to control the electric appliances. If the electric appliance is not in the list of supported devices, you can add the electric appliance through " Customlize ". However, this function is available only for the electric appliance that supports infrared control.
The functions related to camera PTZ control are unavailable temporarily in Apple Home APP until the subsequent update version supports such functions. However, the camera can be controlled the rotation of the PTZ via the Aqara Home APP.
You can scan the QR code to connect Aqara Smart Camera G2H (Hub) to the network. After the device is powered on, please open the app and connect the device to 2.4GHz Wi-Fi, according to the voice prompt. Then, the QR code is generated, and you can scan the QR code through the G2H lens for the network connection.
1. The distance between the device and the wireless router is too far away or there are many obstacles in the middle. When the Wi-Fi signal is weak, the network connection may be unsuccessful. Please use a Wi-Fi signal amplifier to relay the signal or move the router close to a place where the device can receive the Wi-Fi signal well 2. When the wrong Wi-Fi information is entered, the network connection cannot be completed. Please enter the correct information and try again.
The hub of Aqara Smart Camera G2H (Hub) can be connected with Aqara's other smart sensors and controllers, such as door and window sensor, motion sensor, smart plug, wireless switch and other devices. Through the hub function, you can control these smart devices by app. The hub is the data interaction and control center of the entire home smart devices.
The hub of Aqara Smart Camera G2H (Hub) can be connected through the ZigBee 3.0 protocol, and it can directly support 32 Zigbee terminal devices at most.
Aqara Smart Camera G2H (Hub) supports MicroSD card in FAT32 format, whose reading and writing speed is Class 4 or above. It is recommended to choose the MicroSD card with reading and writing speed of Class10 or above, which supports the maximum capacity of 32GB.
Aqara Smart Camera G2H (Hub) can record high-definition video by default. 8G memory card can record video for 18 hours; 16G memory card can record video for 36 hours; 32G memory card can record video for about 3 days.
1. Some knockoffs of small-capacity memory cards pretend to be sold as large-capacity cards; 2. After some devices have been tested, the MicroSD cards could be maliciously partitioned, and the devices can only read the partition partially; 3. Because the manufacturer's capacity formula is different (the actual measurement unit of normal capacity is 1024KB=1MB, and the manufacturer measurement unit is 1000KB=1MB.), the actual capacity will be slightly smaller than that on the nameplate.
The correlation event means that Aqara Smart Camera G2H (Hub) can be correlated with devices in the same home, such as when door and window sensor is triggered, after detecting human motion, the hub can help locate the time position of the event in the recording area. The maximum number of correlation events is 100. Set a correlation event: click the app > "Correlation events" in the lower right corner > select the trigger device for the correlation event > select the color > save.
There is no limit to the number of clients, and it is recommended that 4 users watch at the same time at most, because the more clients the hub is connected with, the more resources the processor consumes (too many client connections will cause real-time image to freeze, delay, etc.)
After adding the device to the Apple Home app, you need to install a HomePod, Apple TV (tvOS 11.0 or later) or an iPad (iOS 12.0 or later) that has been set as the home center to realize remote control. For specific operations, please refer to the Apple Home app instructions.
The bracket base of Aqara Smart Camera G2H (Hub) contains two powerful magnets, which support magnetic attraction on refrigerators, iron door and other objects, and can also be stuck to non-magnetic attraction objects by using the 3M tape and iron pieces in the accessories. Please use them to install the bracket.
Enter the app, click on the “...” in the upper right corner > More settings > Camera settings > Video settings > Image inversion, and correct the video image by adjusting it up and down or left and right.
1) Download the Aqara Home app, enter the Smart Lock U100 page, and complete the installation following the instructions. 2) Scan the QR code for the installation video on the user manual. 3) Scan the QR code for the detailed installation instructions on the electronic user manual.
1) FCC 2) Complies with the same safety standard as BHMA Level 3 3) HomeKit Certification 4) CA65 5) IP65, 200,000 sets of auto-locking/unlocking tests
1) Open the battery cover and knob cover, and remove the battery. 2) Rotate the knob quickly to check if it is effortless to lock and unlock, if you feel any jamming, unscrew and remove the back panel. 3) Check to see if there is any interference between the connector cable and the cylinder tailpiece - excessive friction may affect the door lock's functionality and reduce its battery life. 4) Check to see if the tailpiece is placed in the center of the deadbolt hole; if not, reposition the mounting plate to make sure that the tailpiece is in the center. 5) If the problem still lingers, check to see if the door opening size meets requirements, and if the door frame's opening is on the same level as door lock. Make sure that the deadbolt hole meets Deadbolt door lock's requirements. 6) In the case that the tailpiece curves, causing failure to unlock normally, please contact our customer service center.
1) In Aqara Home app, enter Smart Lock U100 page, then enter 「Settings＞User Guide」 and follow the guidelines to recalibrate the door lock's angle. 2) Close and lock the door manually indoors, then wait for 3 s, by when the door lock will recalibrate its angle; then unlock and test it.
1) In Aqara Home app, enter Smart Lock U100 page, then enter 「Settings＞User Guide」 and follow the guidelines to recalibrate the door lock's angle. 2) Check again to see if the door lock is correctly installed. 3) If the problem still lingers, please contact our customer service center.
Your disassembly of Smart Lock U100 is construed as your agreement to waive the maintenance service of Aqara. If it's acceptable, take the following steps: 1) Loosen the screw of the front lock and take out the original lock cylinder. 2) Buy a new lock cylinder in the same size as the original one, then replace the original with the new one. Note: The lock cylinder used for the U100 is a less common specification and is not the same as the Schlage. Please ask a locksmith has a check if they support a replacement.
The touch panel is made of matte IML, providing superior transparency. The outdoor panel is made of zine alloy with frosted coating, providing increased hardness. The indoor panel is made of plastic and covered by metallic coating, providing effective protection from scratches and residue.
The Aqara Smart Door Lock U100 is equipped with an alloy mechanical lock cylinder. Our locks have been tested to the same requirements as BHMA Class 3.
Open the rear battery compartment cover at the rear of the lock; press and hold the reset key under the battery compartment for over 3 seconds; follow voice prompts and the lock will be reset after admin permissions are verified.
The Aqara Smart Door Lock U100 currently only supports lock status detection, including locked, unlocked, and lock failure. Future OTA may support door status detection, please pay attention to Aqara updates.
The average battery life is 8 months, but varies according to different working environments and conditions. Battery performance declines under low-temperature environments. Battery life was measured by the Aqara laboratory with LR6 AA batteries, and simulated with 8 door openings and 8 auto-lockings a day, under 25℃.
1) If you are outside, you can supply power to the lock through the emergency USB-C charging port at the button of the outer panel. 2) If you are inside, directly replace the LR6 AA batteries.
No, the Aqara Smart Door Lock U100 is well-designed to defend itself from electromagnetic interference and has undergone rigorous electromagnetic compatibility tests. Tesla Coil is a type of ultra-high voltage discharge equipment. Its electromagnetic induction may damage precision electronic devices within a certain radius, but it does not affect the normal operation of the Aqara Smart Door Locks.
The Aqara Smart Door Lock U100 supports 9 ways of unlocking: 1) Fingerprint 2) Password (ordinary, one-time, periodic) 3) HomeKit / Siri (Bluetooth, Remote, Apple Home Key) 4) Aqara Home (Bluetooth, Remote) 5) Google Home / Google Assistant (Remote) 6) Amazon Alexa/ Alexa (Remote) 7) NFC Card (Aqara and Mifare M1 Card) 8) Integration unlock via Aqara G4 doorbell 9) Mechanical Key *Aqara Home app and HomeKit support Bluetooth short-range unlocking. *Aqara Home app, HomeKit, Google Home, and Alexa support remote unlocking, on condition that there is a supporting hub at home. *Siri/Google Assistant/Alexa voice control is effective, but an Apple Hub is required for Siri and an Aqara Hub is required for Google Home and Alexa.
The keyboard will not be locked due to successive password/fingerprint/NFC verification failures by default for now. However, it will be locked down in the future OTA. Within these few minutes, the lock can be controlled through apps (Aqara Home/Apple Home/Google Home/Alexa) OR unlocked with a mechanical key. After a few minutes, all verification functions return to normal. You also can change the setting through Aqara Home app.
The mechanical key is usually used for emergency situations when the lock cannot be unlocked by normal verification methods (fingerprint/password/mobile app/NFC/HomeKey). It is recommended to keep the key in your car or office, just in case.
The Aqara Smart Door Lock U100 supports up to 75 passwords at the same time, including ordinary and temporary periodic passwords. In addition, up to 8 sets of one-time passwords can be generated per hour.
6- to 10-digit lock passwords are supported. Phantom passwords are supported, up to a total of 20 digits (including 6-10 digits of a lock password). The phantom password function adds arbitrary numbers before or after a lock password to prevent peeping from intruders when you enter the password.
Yes, a periodic password for a specified timespan (e.g. 10am-2pm) and a specified period (e.g. every Monday) can be set up with the Aqara Home app, when the app is connected to the lock via Bluetooth OR remotely (hub required). This type of password can unlock the door during a designated time period.
If the Aqara Smart Door Lock U100 prompts an unsuccessful fingerprint entry, make sure that the finger used for the fingerprint is dry and the fingerprint is not damaged substantially. It takes seven times to collect a complete fingerprint. Please fully press the finger on the identification area and try to change the input angle according to the voice/Aqara Home app prompts (avoid repeated inputs at the same angle). For a better unlocking experience, it is recommended to enter the print of the thumb of the commonly used hand.
Please make sure the finger is not stained or wet, press the finger fully onto the identification area, and try again. If repeated failure results in fingerprint verification being locked out, use a password, delete the old fingerprint on the Aqara Home app, and set up a new one. Multiple groups of fingerprints can be set to avoid verification failure due to problems on a single finger.
The fingerprint module unlocks after identifying, comparing, and verifying the collected fingerprint pattern. The success rates of fingerprint unlocking are affected by an elder's serious fingerprint wear and children's shallow/incomplete fingerprint patterns. Password and NFC/HomeKey are recommended in such cases.
After unlocking the door, many traditional electronic locks of other brands will have their latch bolt relocked five to ten seconds later. During this period, intruders can open the door by pressing the handle, which is a security risk. Aqara Smart Door Lock U100 can detect the door is closed and automatically locks immediately, preventing intruders unlocking and tailing effectively.
Install the Aqara Home app on your phone and add the lock to it. Click the unlock icon on the home page of the app and then press the handle to unlock it. With the lock added to the Aqara Home app, it can also be added to HomeKit and unlocked via Bluetooth.
Yes, the Aqara Smart Door Lock U100 can be unlocked remotely through the mobile app. 1) Aqara Home app: Click the open button in the app. The door lock needs to be connected to an Aqara Hub at home. 2) HomeKit: Click the open button in the app or use Siri voice control. The door lock needs to be connected to an Apple Hub at home. (HomePod/iPad/Apple TV). 3) Google Home/Amazon Alexa: click the button in the app or use the voice control, and provide the preset unlocking password. The door lock needs to be connected to an Aqara Hub at home.
Yes, the Aqara Smart Door Lock U100 can be unlocked by voice control. The Aqara Home app does not support voice control. HomeKit supports Siri voice unlocking; in short range, Bluetooth and cellphone internet access are required; remotely, cellphone internet access and lock connected to an Apple Home Hub (HomePod/iPad/Apple TV) are required. Google Home/Alexa supports OK Google/Alexa voice unlocking; the Google Assistant/Amazon Alexa device requires internet access, a preset unlocking password is required, and the door lock should be connected to an Aqara Hub at home.
The initial admin account is set when the lock is added to the Aqara Home app for the first time. The admin account is required to enter the local setting mode. The initial admin account can add more admin accounts on the Aqara Home app.
First, a system with an iPhone iOS 15 or higher or an Apple Watch OS 8 or higher is required. After adding the Aqara Smart Door Lock U100 to HomeKit, a virtual door card (an Apple Home Key) will be generated in the Apple Wallet. If your Apple Watch is used at the same time, the door card will be copied to the wallet app of your Watch.
Apple Home Key is a virtual door card based on Apple NFC technology, which supports standard and shortcut modes. In standard mode, open the Apple Wallet, select the door card, and move the iPhone/Watch close to the NFC identification area of the door lock for verification and unlocking. In shortcut mode, HomeKit will actively prompt the user to set the door card on the shortcut. The user can start the shortcut mode after verifying the Face ID or password. In shortcut, the user needs to unlock the iPhone/Watch and move the device close to the NFC identification area of the door lock for verification and unlocking.
You can invite other Apple users to join the family of users on the HomeKit app. Other users, after joining, will have a copy of the door card automatically generated in their Wallet.
A: The touch panel is made of IML, providing superior transparency. The rest is made of frosted aluminum alloy, providing increased hardness. The fingerprint identification module is covered by glass, providing effective protection from scratches and residue.
A: The touch panel is made of IML, providing superior transparency. The rest is made of frosted aluminum alloy, providing increased hardness. The fingerprint identification module is covered by glass, providing effective protection from scratches and residue.
A: A true-insert, with its lock cylinder embedded into the lock body, has a more complex structure than a false-insert: a mechanical key is required to open the lock when the front panel is damaged/removed, which is more secure because flase-insert can be opened without a mechanical key when the front panel is damaged/removed.
A: A true-insert, with its lock cylinder embedded into the lock body, has a more complex structure than a false-insert: a mechanical key is required to open the lock when the front panel is damaged/removed, which is more secure because flase-insert can be opened without a mechanical key when the front panel is damaged/removed.
A: First, you need to add the door lock to the Aqara Home app, set an admin fingerprint/password for the lock following the prompts. Second, press the setup button on the battery compartment on the rear panel and verify the admin fingerprint/password to enter setup mode. Third, continue settings according to the voice prompts.
A: First, you need to add the door lock to the Aqara Home app, set an admin fingerprint/password for the lock following the prompts. Second, press the setup button on the battery compartment on the rear panel and verify the admin fingerprint/password to enter setup mode. Third, continue settings according to the voice prompts.
A: Open the rear battery compartment cover at the rear of the lock; press and hold the reset key under the battery compartment for over 5 seconds; follow voice prompts and the lock will be reset after admin permissions are verified.
A: Open the rear battery compartment cover at the rear of the lock; press and hold the reset key under the battery compartment for over 5 seconds; follow voice prompts and the lock will be reset after admin permissions are verified.
A: The Aqara Smart Door Lock D100 provides detection to all spring bolts, which together help determine the door's closing and locking state. The Aqara Home app displays all possible states of your door, including: open closed but unlatched latched and locked
The Aqara Home app，Apple HomeKit app and the Google Home app can display two states, open and closed.
A: The Aqara Smart Door Lock D100 provides detection to all spring bolts, which together help determine the door's closing and locking state. The Aqara Home app displays all possible states of your door, including: open closed but unlatched latched and locked
The Aqara Home app，Apple HomeKit app and the Google Home app can display two states, open and closed.
A: The lock cylinder of the Aqara Smart Door Lock D100 is compatible with most wooden, metal and armored doors on the market, whose thickness is between 40mm and 80mm. For doors with a thickness of 80mm-120mm, please contact the local dealer for a longer lock cylinder.
A: The lock cylinder of the Aqara Smart Door Lock D100 is compatible with most wooden, metal and armored doors on the market, whose thickness is between 40mm and 80mm. For doors with a thickness of 80mm-120mm, please contact the local dealer for a longer lock cylinder.
A: The average battery life is 12 months, but varies according to different working environment and conditions. Battery performance declines under low temperature environments. *Battery life was measured by the Aqara laboratory with a lithium battery, and simulated with 10 door openings a day, under 25℃.
A: The average battery life is 12 months, but varies according to different working environment and conditions. Battery performance declines under low temperature environments. *Battery life was measured by the Aqara laboratory with a lithium battery, and simulated with 10 door openings a day, under 25℃.
A: When power is lower than 20%, the lock will generate prompt sounds and the Aqara Home app will receive alerts. Please charge the lithium battery after receiving notices.
A: When power is lower than 20%, the lock will generate prompt sounds and the Aqara Home app will receive alerts. Please charge the lithium battery after receiving notices.
A: ①If you are outside, you can supply power to the lock through the TYPE-C charging interface at the button of the outer panel. ②If you are inside, Take out the lithium battery and charge it with USB-C charging cable. ③If you are inside, Directly charge the battery by connecting the USB-C charging cable to the indoor back panel.
A: ①If you are outside, you can supply power to the lock through the TYPE-C charging interface at the button of the outer panel. ②If you are inside, Take out the lithium battery and charge it with USB-C charging cable. ③If you are inside, Directly charge the battery by connecting the USB-C charging cable to the indoor back panel.
A: No, the Aqara Smart Door Lock D100 is a well-designed to defend itself from electromagnetic interference and has undergone rigorous electromagnetic compatibility tests. *Tesla Coil is a type of ultra-high voltage discharge equipment. Its electromagnetic induction may damage precision electronic devices within a certain radius, but it does not affect the normal operation of the Aqara Smart Door Locks.
A: No, the Aqara Smart Door Lock D100 is a well-designed to defend itself from electromagnetic interference and has undergone rigorous electromagnetic compatibility tests. *Tesla Coil is a type of ultra-high voltage discharge equipment. Its electromagnetic induction may damage precision electronic devices within a certain radius, but it does not affect the normal operation of the Aqara Smart Door Locks.
A: 1. The function operates to prevent lawless persons from destroying the cat-eye and putting special tools into the room to press the one-touch unlock button to unlock. 2. The Aqara Smart Door Lock D100 is designed with cat-eye prevention unlocking (child lock). It can open the child lock around the indoor unlock button when leaving home, preventing the door from being opened by pressing the indoor button and preventing children or pets from unlocking the door by touching the button accidentally.
A: 1. The function operates to prevent lawless persons from destroying the cat-eye and putting special tools into the room to press the one-touch unlock button to unlock. 2. The Aqara Smart Door Lock D100 is designed with cat-eye prevention unlocking (child lock). It can open the child lock around the indoor unlock button when leaving home, preventing the door from being opened by pressing the indoor button and preventing children or pets from unlocking the door by touching the button accidentally.
A: The Aqara Smart Door Lock D100 child lock switch（combined with cat-eye prevention unlocking） is designed to prevent children or pets from unlocking by mistake. Turn the child lock switch to the right position to release the lock of the button before unlock from indoors, effectively prevent youngger children to unlock the door by mistake alone at home, Turn the child lock switch to the left position will improve the safety level of the door lock. After the child lock is opened, the lock can only be opened by using the indoor emergency unlocking knob or unlocking from outdoor.
A: The Aqara Smart Door Lock D100 child lock switch（combined with cat-eye prevention unlocking） is designed to prevent children or pets from unlocking by mistake. Turn the child lock switch to the right position to release the lock of the button before unlock from indoors, effectively prevent youngger children to unlock the door by mistake alone at home, Turn the child lock switch to the left position will improve the safety level of the door lock. After the child lock is opened, the lock can only be opened by using the indoor emergency unlocking knob or unlocking from outdoor.
A: The Aqara Smart Door Lock D100 supports 7 ways of unlocking:
Fingerprint Password (ordinary, one-time, periodic) HomeKit / Siri (Bluetooth, Remote, Apple Home Key) Aqara Home (Bluetooth, Remote) Google Home / Google Assistant (Remote) NFC Card (M1 Card) Mechanical Key
*Aqara Home app and HomeKit support Bluetooth short-range unlocking. *Aqara Home app, HomeKit and Google Home support remote unlocking, on condition that there is a supporting hub at home. *Siri/Google Assistant voice control is effective, but an Apple Hub is required for Siri and an Aqara Hub is required for Google Assistant.
A: The Aqara Smart Door Lock D100 supports 7 ways of unlocking:
Fingerprint Password (ordinary, one-time, periodic) HomeKit / Siri (Bluetooth, Remote, Apple Home Key) Aqara Home (Bluetooth, Remote) Google Home / Google Assistant (Remote) NFC Card (M1 Card) Mechanical Key
*Aqara Home app and HomeKit support Bluetooth short-range unlocking. *Aqara Home app, HomeKit and Google Home support remote unlocking, on condition that there is a supporting hub at home. *Siri/Google Assistant voice control is effective, but an Apple Hub is required for Siri and an Aqara Hub is required for Google Assistant.
A: The keyboard will be locked for 3 minutes due to successive password/fingerprint/NFC verification failures. Within 3 minutes, the lock can be controlled through apps (Aqara Home/HomeKit/Google Home) OR unlocked with a mechanical key. After 3 minutes, all verification functions return to normal.
A: The keyboard will be locked for 3 minutes due to successive password/fingerprint/NFC verification failures. Within 3 minutes, the lock can be controlled through apps (Aqara Home/HomeKit/Google Home) OR unlocked with a mechanical key. After 3 minutes, all verification functions return to normal.
A: The mechanical key is usually used for emergency situations when the lock cannot be unlocked by normal verification methods (fingerprint/password/mobile app/NFC). It is recommended to keep the key in your car or office, just in case.
A: The mechanical key is usually used for emergency situations when the lock cannot be unlocked by normal verification methods (fingerprint/password/mobile app/NFC). It is recommended to keep the key in your car or office, just in case.
A: 6- to 10-digit lock passwords are supported. Phantom passwords are supported, up to a total of 20-digits (including 6-10 digits of a lock password). *Phantom password function adds arbitrary numbers before or after a lock password to prevent peeping from intruders when you enter the password.
A: 6- to 10-digit lock passwords are supported. Phantom passwords are supported, up to a total of 20-digits (including 6-10 digits of a lock password). *Phantom password function adds arbitrary numbers before or after a lock password to prevent peeping from intruders when you enter the password.
A: Yes, a periodic password for a specified timespan (e.g. 10am-2pm) and a specified period (e.g. every Monday) can be set up with the Aqara Home app, when the app is connected to the lock via Bluetooth OR remotely (hub required). This type of password can unlock the door during a designated time period.
A: Yes, a periodic password for a specified timespan (e.g. 10am-2pm) and a specified period (e.g. every Monday) can be set up with the Aqara Home app, when the app is connected to the lock via Bluetooth OR remotely (hub required). This type of password can unlock the door during a designated time period.
A: Yes. When any verification certificate (fingerprint/password/NFC card) is wrong for 5 consecutive times, the lock sets out alarm sound and light, verification functions are temporarily locked out, and an alarm message is sent to the Aqara Home app.
A: Yes. When any verification certificate (fingerprint/password/NFC card) is wrong for 5 consecutive times, the lock sets out alarm sound and light, verification functions are temporarily locked out, and an alarm message is sent to the Aqara Home app.
A: There are two ways to set fingerprints: ①Install the Aqara Home app, after the lock is added and connected to the app, set the fingerprint according to app prompts. ②Lift the battery cover at the rear, press the setup button above the battery compartment, and set the fingerprint according to the voice prompts. *The lock has be to added to the app before local mechanical buttons can be used to set a fingerprint.
A: There are two ways to set fingerprints: ①Install the Aqara Home app, after the lock is added and connected to the app, set the fingerprint according to app prompts. ②Lift the battery cover at the rear, press the setup button above the battery compartment, and set the fingerprint according to the voice prompts. *The lock has be to added to the app before local mechanical buttons can be used to set a fingerprint.
A: ①Make sure that the finger used for fingerprint is dry and the fingerprint is not damaged substantially. ②It takes seven times to collect a complete fingerprint. Please fully press the finger on the identification area and try to change the input angle according to the voice/Aqara Home app prompts (avoid repeated inputs at the same angle). ③For better unlocking experience, it is recommended to enter the print of the thumb of the commonly used hand.
A: ①Make sure that the finger used for fingerprint is dry and the fingerprint is not damaged substantially. ②It takes seven times to collect a complete fingerprint. Please fully press the finger on the identification area and try to change the input angle according to the voice/Aqara Home app prompts (avoid repeated inputs at the same angle). ③For better unlocking experience, it is recommended to enter the print of the thumb of the commonly used hand.
A: Please make sure the finger is not stained or dry, press the finger fully onto the identification area and try again. If repeated failure results in fingerprint verification being locked out, use a password, delete the old fingerprint on Aqara Home app, and setup a new one. Multiple groups of fingerprints can be set to avoid verification failure due to problems on a single finger.
A: Please make sure the finger is not stained or dry, press the finger fully onto the identification area and try again. If repeated failure results in fingerprint verification being locked out, use a password, delete the old fingerprint on Aqara Home app, and setup a new one. Multiple groups of fingerprints can be set to avoid verification failure due to problems on a single finger.
A: Yes. the Aqara Smart Door Lock D100 prevents test-unlocking of fingerprints in two ways: ①We use a customized algorithm from Swedish Precise Biometrics (PB) to effectively eliminate false fingerprint unlocking. ②When any verification certificate (fingerprint/password/NFC card) is wrong for 5 consecutive times, the lock sets out alarm sound and light, verification functions are temporarily locked out, and an alarm message is send to the Aqara Home app.
A: Yes. the Aqara Smart Door Lock D100 prevents test-unlocking of fingerprints in two ways: ①We use a customized algorithm from Swedish Precise Biometrics (PB) to effectively eliminate false fingerprint unlocking. ②When any verification certificate (fingerprint/password/NFC card) is wrong for 5 consecutive times, the lock sets out alarm sound and light, verification functions are temporarily locked out, and an alarm message is send to the Aqara Home app.
A: The fingerprint module unlocks after identifying, comparing, and verifying the collected fingerprint pattern. The success rates of fingerprint unlocking are affected by an elder's serious fingerprint wear and children's shallow/incomplete fingerprint patterns. Password and NFC are recommended in such cases.
A: The fingerprint module unlocks after identifying, comparing, and verifying the collected fingerprint pattern. The success rates of fingerprint unlocking are affected by an elder's serious fingerprint wear and children's shallow/incomplete fingerprint patterns. Password and NFC are recommended in such cases.
A: After unlocking the door, many traditional electronic locks of other brands will have their latch bolt relocked five to ten seconds later. During this period, intruders can open the door by pressing the handle, which is a security risk. Aqara Smart Door Lock D100 detectsthe door is closed and automatically locks immediately, preventing intruder unlocking and tailing effectively.
A: After unlocking the door, many traditional electronic locks of other brands will have their latch bolt relocked five to ten seconds later. During this period, intruders can open the door by pressing the handle, which is a security risk. Aqara Smart Door Lock D100 detectsthe door is closed and automatically locks immediately, preventing intruder unlocking and tailing effectively.
A: ①Install the Aqara Home app on your phone and add the lock to it. Click the unlock icon on the home page of the app and then press the handle to unlock it. ②With the lock added to the Aqara Home app, it can also be added to HomeKit and unlocked via Bluetooth.
A: ①Install the Aqara Home app on your phone and add the lock to it. Click the unlock icon on the home page of the app and then press the handle to unlock it. ②With the lock added to the Aqara Home app, it can also be added to HomeKit and unlocked via Bluetooth.
A: Yes. ①Aqara Home app: Click the open button in the app. The door lock needs to be connected to an Aqara Hub at home. ②HomeKit: Click the open button in the app or use Siri voice control. The door lock needs to be connected to an Apple Hub at home (HomePod/iPad/Apple TV). ③Google Home: click the button in the app or use the Ok Google voice control, and provide the preset unlocking password. The door lock needs to be connected to an Aqara Hub at home.
A: Yes. ①Aqara Home app: Click the open button in the app. The door lock needs to be connected to an Aqara Hub at home. ②HomeKit: Click the open button in the app or use Siri voice control. The door lock needs to be connected to an Apple Hub at home (HomePod/iPad/Apple TV). ③Google Home: click the button in the app or use the Ok Google voice control, and provide the preset unlocking password. The door lock needs to be connected to an Aqara Hub at home.
A: Yes. ①Aqara Home app: Not supported. ②HomeKit: Support Siri voice unlocking. In short range, Bluetooth and the cellphone Internet access are required; remotely, cellphone internet access and lock connection to an Apple Home Hub (HomePod/iPad/Apple TV) are required. ③Google Home: Support OK Google voice unlocking. The Google Assistant device requires internet access, a preset unlocking password is required, and the door lock should be connected to an Aqara Hub at home.
A: Yes. ①Aqara Home app: Not supported. ②HomeKit: Support Siri voice unlocking. In short range, Bluetooth and the cellphone Internet access are required; remotely, cellphone internet access and lock connection to an Apple Home Hub (HomePod/iPad/Apple TV) are required. ③Google Home: Support OK Google voice unlocking. The Google Assistant device requires internet access, a preset unlocking password is required, and the door lock should be connected to an Aqara Hub at home.
A: The Aqara Smart Door Lock D100 alarms are triggered when the door is unclosed, closed but unlatched, lock is ransacked，abnormal lock status，low battery, repeated verification failures, indoor/mechanical key opening in away mode. Both mobile apps and local alarms are enabled in these cases.
A: The Aqara Smart Door Lock D100 alarms are triggered when the door is unclosed, closed but unlatched, lock is ransacked，abnormal lock status，low battery, repeated verification failures, indoor/mechanical key opening in away mode. Both mobile apps and local alarms are enabled in these cases.
A: The initial admin account is set when the lock is added to Aqara Home app for the first time. Admin account is required to enter local setting mode. The initial admin account can add more admin accounts on Aqara Home app.
A: The initial admin account is set when the lock is added to Aqara Home app for the first time. Admin account is required to enter local setting mode. The initial admin account can add more admin accounts on Aqara Home app.
A: First, a system with an iPhone iOS 15 or higher or an Apple Watch OS 8 or higher is required. After adding the Aqara Smart Door Lock D100 to HomeKit, a virtual door card (an Apple Home Key) will be generated in the Apple Wallet. If your Apple Watch is used at the same time, the door card will be copied to the wallet app of your Watch.
A: First, a system with an iPhone iOS 15 or higher or an Apple Watch OS 8 or higher is required. After adding the Aqara Smart Door Lock D100 to HomeKit, a virtual door card (an Apple Home Key) will be generated in the Apple Wallet. If your Apple Watch is used at the same time, the door card will be copied to the wallet app of your Watch.
A: Apple Home Key is a virtual door card based on Apple NFC technology, which supports standard and shortcut modes. Standard mode: open the Apple Wallet, select the door card, and move iPhone/Watch close to the NFC identification area of the door lock for verification and unlocking. Shortcut mode: HomeKit will actively prompt the user whether to set the door card on shortcut. The user can start the shortcut mode after verifying the Face ID or password. In shortcut, the user needs to unlock the iPhone/Watch and move the device close to the NFC identification area of the door lock for verification and unlocking.
A: Apple Home Key is a virtual door card based on Apple NFC technology, which supports standard and shortcut modes. Standard mode: open the Apple Wallet, select the door card, and move iPhone/Watch close to the NFC identification area of the door lock for verification and unlocking. Shortcut mode: HomeKit will actively prompt the user whether to set the door card on shortcut. The user can start the shortcut mode after verifying the Face ID or password. In shortcut, the user needs to unlock the iPhone/Watch and move the device close to the NFC identification area of the door lock for verification and unlocking.
A: You can invite other Apple users to join the family of users on the HomeKit app. Other users, after joining, will have a copy of the door card automatically generated in their Wallet.
A: You can invite other Apple users to join the family of users on the HomeKit app. Other users, after joining, will have a copy of the door card automatically generated in their Wallet.
Aqara smart door lock A100 Zigbee supports fingerprint unlocking, password unlocking, card unlocking, temporary password unlocking, mobile phone unlocked via Bluetooth, HomeKit unlocked via Bluetooth, and emergency key unlocking, a total of 7 unlocking methods.
There are two ways to enroll fingerprints: 1. After installing the Aqara Home App on the mobile phone to add a door lock and connect the door lock, enter fingerprints according to the operation prompts of the APP. 2. After opening the rear panel of the door lock, short press the setting button above the battery compartment of the door lock, and enter fingerprints according to the voice navigation prompt (you need to add the door lock through the Aqara Home App first and then enable the local setting function).
Please make sure your finger is not dirty, too wet or too dry, and press your finger completely on the fingerprint recognition area to try again. If the fingerprint recognition fails continuously until the fingerprint identification is locked, you can unlock it with a password first, delete the fingerprint on the App and re-enter it. When entering fingerprints, you can enter multiple groups to avoid verification failure caused by a single finger fingerprint problem.
Aqara smart door lock A100 Zigbee supports the setting of 6-10-digit unlock passwords, and supports 20-digit virtual-digit passwords (the virtual-digit passwords include 6-10-digit unlock passwords, and the combination of unlock passwords and virtual-digit passwords is within 20 digits) . (*Dummy password refers to adding any garbled characters before or after entering the correct unlock password to prevent others from peeping when entering the password)
Install the Aqara Home App on your mobile phone and add a door lock through the App, enter the door lock page, press and hold the unlock icon, and then press down on the door handle to unlock.
Aqara smart door lock A100 Zigbee has a lift-up quick lock design, which can be quickly was locked indoors or outdoors by lifting the door handle to improve the security level of the door lock.
Aqara smart door lock A100 Zigbee alarm reminders are as follows: The door lock was picked, the battery is low, and the authentication failed many times.
The theoretical battery life of the door lock is 18 months, and the actual battery life will vary depending on the actual use environment. The performance of the battery in a low-temperature environment will decrease, and the battery life will be shortened. Note: The battery life is measured by Lumi Lab under the conditions of using 8 original battery, simulating opening the door 10 times a day (not double verification mode), and normal temperature 25°C.
If the battery of the door lock is out of power, the Aqara smart door lock A100 Zigbee emergency charging interface can be used to supply power and unlock the lock. The emergency charging interface is in the form of Type-C and is located at the bottom of the outer panel of the door lock. It can supply power to the door lock.
The Aqara smart door lock A100 Zigbee does not support the Bawang lock body for the time being. It can be installed with the standard lock body and the Bawang lock body face plate.
Administrators have the following permissions: You can enter the local setting mode of the door lock through the administrator's fingerprint or password to set, you can restore the door lock to factory settings, you can unlock the door from the locked state outdoors, and you can also unlock it daily.
Open the rear cover of the door lock, find the reset button under the battery compartment, press and hold it for more than 5 seconds to verify the administrator's identity according to the prompt, and then the door lock can be reset.
The dry battery voltage of the door lock needs to reach 1.5V. If the actual battery voltage purchased by the user is lower than 1.5V, it may cause the low battery warning to appear after the new battery has been used for a few days.
The standard package of Aqara Smart Door Lock N100 include: Open-hole drawing x 1 Manual x 1 Front panel x 1 Back panel x 1 Lock body x 1 Door buckle plate x 1 Door buckle box x 1 Some fixed screws Mechanical lock cylinder x 1 Mechanical key x 2 AA battery x 8 Large square shaft x 1 Small square shaft x 1 Panel screw x 2 Stud x 2 Fixed screw x 2
The security level of Aqara Smart Door Lock N100 is B class, and the security level of the lock cylinder is C class. Both of them are the highest level. (according to the door lock industry standard GA/T 73-2015 Mechanical Anti-theft Lock compiled by the Ministry of Public Security of the People's Republic of China)
① Anti-peephole unlock function is to prevent criminals from damaging the peephole by using a special tool to reach into the room and push down the handle to unlock the door; ② Aqara Smart Door Lock N100 has anti-peephole unlock design. When you want to open the door, you must press the anti-peephole button on the indoor handle and push down the door handle to unlock the door.
Aqara Smart Door Lock N100 supports 6 unlocking methods, including unlocking with fingerprint, unlocking with password, unlocking with NFC card, unlocking with temporary password, unlocking with HomeKit Bluetooth and unlocking with emergency key.
There are two ways as follows: ①After installing the Aqara Home app on the mobile phone, please add and connect the door lock, and then register a fingerprint according to the operation prompts of the app; ②After opening the back panel of the door lock, please short press the Set button above the battery compartment of the door lock and register a fingerprint according to voice prompts (you need to add the door lock through the Aqara Home app and then enable the Local Settings function).
1. Please make sure that the finger is dry, and its fingerprint is not damaged in a large area; 2. During the process of fingerprint registration (you need to register the fingerprint 7 times to complete its registration successfully), please fully press your finger on the fingerprint recognition area, and try to change the fingerprint registration angle according to the voice or app prompts (do not repeat the same angle); 3. For a better unlocking experience, it is recommended to register the thumb.
Aqara Smart Door Lock N100 prevents unlocking by multiple trials from two aspects to ensure security: ①Aqara Smart Door Lock N100 adopts PB in-depth customization algorithm, which can effectively prevent unlocking the door with fake fingerprint; ②After fingerprint recognition fails 5 times continuously, the door lock will trigger the local alarm (the door lock will play an alarm sound and turn on alarm light), lock the fingerprint recognition function, and send an alarm notification to the app; ③Aqara Smart Door Lock N100 fingerprint module adopts the latest self-learning algorithm. The more frequently it is used, the more sensitive it is.
Aqara Smart Door Lock N100 supports unlocking password with 6-10 digits, and virtual password with 20 digits (virtual password includes the unlock password with 6-10 digits, and the combination of unlocking password and virtual password is within 20 digits). (*virtual password refers to adding random codes before or after entering the correct unlocking password to prevent others from peeping when entering the password)
Temporary password include one-time temporary password and periodic temporary password. ① After the door lock is added to the Aqara Home app, one-time temporary password can be created anytime and anywhere (Bluetooth and hub are not required to be connected with the door lock.). One-time temporary password can only be used once after being created, and the validity period is within 20 minutes. ② Periodic temporary password does not support remote creation and can only be created when the Bluetooth of the mobile phone is normally connected with the door lock. Periodic temporary password (nanny password) can be set to be valid within a specified time period (for example: 10:00~11:00), or certain days of every month or week. The temporary password can only be used during the valid time period.
You can use other methods to unlock the door, such as using fingerprint, HomeKit, NFC card or emergency key to unlock. After unlocking the door, the keyboard will be unlocked and will not affect the next use.
Only HomeKit remote unlock function is supported. HomeKit remote unlock function requires to pair the door lock with a home hub; when connected to the Aqara Home app, the door lock does not have remote unlock function.
After the traditional electronic lock is unlocked, it usually takes 5-10s to lock the door again. During this time period, other people can push down the handle to open the door again. It will be dangerous if the bad guy is trailing behind. The handle of Aqara Smart Door Lock N100 rebounds immediately to lock the door to prevent the possibility of pushing down the handle again to unlock the door, which effectively prevents trailing.
Aqara Smart Door Lock N100 has the design to lift the handle to lock the door quickly, which can quickly lock the door by lifting the door handle indoors or outdoors to improve the security level of the door lock.
Locking from inside function can only be operated indoors. After being locked from inside, the security level of the door lock will be improved. Only the administrator's fingerprint or password can be used to unlock the door outdoors. Other users cannot use fingerprint, password or NFC card to unlock.
When the door is locked from inside, you can use the administrator's fingerprint or password to unlock the door outdoors (the emergency key cannot unlock the door). Ordinary users should contact indoor members to unlock the door.
Aqara Smart Door Lock N100 can detect the open/closed state of the door and the almost closed state of the door. If the door is not closed completely, the door lock will play an alarm sound and send a push notification.
The alarm is off by default when the door is not closed or locked. The alarm function needs to be enabled in the app. After adding and connecting the door lock in the Aqara Home app, please set the function in "Door Lock Settings"-"Unlocked Alarm".
Aqara Smart Door Lock N100 triggers alarm notification function as follows: The door is almost closed; the door is not closed (alarm notification function needs to be enabled in the app); the door is not lifted to be locked or locked from inside (alarm notification function needs to be enabled in the app); the door lock is pried; the battery is low; and the door fails to be unlocked with password, fingerprint or NFC card multiple times.
The theoretical battery life of the door lock is 18 months. The actual battery life will vary depending on the actual use environment. The battery performance in a low temperature environment will decrease and the battery life will be shortened. Note: The battery life is measured by Lumi Lab under the conditions of using 8 original batteries and simulating the door opening 10 times a day (without using double-recognition mode) at room temperature of 25℃.
If the batteries of the door lock is dead, you can use the emergency charging port of Aqara Smart Door Lock N100 to supply power and unlock. The emergency charging port is Type-C, located at the bottom of front panel. Please use a power bank and Type-C cable to supply power for the door lock.
Firstly, there is a ZigBee hub device near Aqara Smart Door Lock N100, and the hub is bound to the same Aqara account; Then, configure the door lock in the "Paired Hub" in door lock device settings page. It is recommended to bind the hub in the Aqara Home app first, and then bind the door lock device according to the app prompts. Before binding the door lock for the first time, you need to reset the door lock.
After Aqara Smart Door Lock N100 connects to ZigBee hub, it can remotely view door lock logs, door lock state, set and execute automations with other smart devices.
N100 supports the Aqara Home app and the Apple Home app, and can be paired and interacted with other smart devices under the Aqara brand or in the Apple Home app (but other devices of Mi Home and Apple are not supported).
The Aqara LED Light Bulb supports adjustable brightness, color temperature, app control, automation connection with other devices, timer switch, delay switch, and other functions.
The Aqara LED Light Bulb can be used as an ordinary light bulb independently. However, if you want to use app control, smart connection or other functions, the bulb must be first bound to an Aqara Hub.
Turn the light bulb on/off 5 times continuously with the physical switch. The bulb is reset successfully when the bulb flashes twice quickly and then stays on.
Yes, the Aqara LED Light Bulb supports Siri, Alexa and Google Home voice control (the bulb must be bound to an Aqara Hub to activate voice control function).
Hello, we use cookies to create the most secure and effective website possible. By using this site, you consent to the use of cookies. Read our
Privacy Policy.
Hi, how can we help you?
